Harken 3838 System B CB & Slider Battcars: built 2005-2006 - Manual (Page 2)

CB System
Part No.
Slider System
Part No. Description Comments
3838 3833 Headboard cars
3839 3836 Intermediate cars If battens are close enough intermediate cars are not needed.
3840 3834 Batten car 10 mm Threaded stud. Purchase batten receptacle separately.
3841 3835 Batten car 12 mm Threaded stud. Purchase batten receptacle separately.
3842 — Universal Battcar Purchase batten receptacle and threaded stud separately.
3843 — Reef Tack car Requires special track with closer hole spacing
Part No. Description Includes
3845, 3846 Track Mounting
Kit
(a) 19 mounting slugs 7 /
8
" (22 mm); (b) 1 connector slug 3" (76 mm);
(c) 2 Tubes Blue Loctite ®
; (d) 21 HFS321 Flathead screws 6 x 20 mm.
3847
3848
Screwpin
Endstop Kit
(e) 1 end track with screwpin stop; (f) 1 top stop slug 1 7 / 16 " (36 mm); (g) 1 top endstop 1522A; (h) 1 mounting slug 7 / 8 "
(22 mm); (i) 2 HFS321 flathead screws 6 x 20 mm; (j) 2 HFS1037 flathead screws 6 x 30 mm; (k) 1 tube blue Loctite ®
.
3850, 3851 Endstop Kit (g) 2 endstops 1522A; (i) 4 HFS1037 flathead screws 6 x 30 mm; (f) 2 stop slugs 1 7 / 16 " (36 mm)
3844 Track (slug type) Section length: 6'9 1 / 8 " (2.06 m). Number of track sections depends on luff length of your mainsail.
1616 Track (drill and
tap type)
Use for masts without grooves or when slugs will not fit. Purchase stainless steel 1 / 4 " (6 mm) screws separately.
Do not use 3844 track. It requires mounting slugs. See page 8 for drill/tap sizes and mounting instructions.
3838
CB
3833
Slider
Thank you for puchasing a Harken
Battcar system. Please read the
manual before assembling
Track Mounting Kit
3845, 3846
a
b
c
d
Spare
Car
Screws
Headboard Cars (Assembly)
Track and Accessories
CB/Slider System Parts
Universal Battcar
e
Intermediate Cars
3840/3841 – CB
3834/3835 – Slider
Batten Cars without Receptacle
3836
Slider
3839
CB
CB/Slider Systems Parts List
3842
CB 3843 – CB
Reef Car
3844
9 /
16
"
( 14 mm) 1616
Track (Mounting Slug Type)
Track (Drill and Tap Type)
9 /
16
"
(14 mm)
1 1 /
16
" (27 mm)
2
Thank you for puchasing Harken's B
Battcar system. Please read manual
before assembling system.
System B (CB/Slider) 4252/12-05
You will need these tools:
Tape Measure
Phillips Screwdriver
Power screwdriver
Drill / Drill Bit: 17 / 64 " (6.5 mm)
Hex wrench: 5 mm
Nut Driver: 10 mm or Open/Box Wrench
Centerpunch / Hammer
Putty knife / Hacksaw / File / Tape
Mast-Up Installation: Stepladder
secured to the boat.
Work Height: 7' (2.13 m) above boom.
f
h
i
j
k
g
Endstop Kits
3850, 3851
Screwpin Endstop Kits
3847, 3848