Gasboy CFN Islander I - Manual (Page 2)

Page 2
Consoles
Console I Provides point of sale capabilities for fuel sales for up
to 16 fueling positions. Features: 20 character alphanumeric
display, 16 pump LEDs, built-in ABA track II mag reader,
manager keyswitch. Handles credit and proprietary cards and
stackable sales. Options: Standalone receipt printer, PIN pad,
cash drawer, customer display.
Check Point Provides point of sale capabilities for fuel and
merchandise sales for Site Controller II only. 20-character
alphanumeric display. Built-in ABA track II mag reader. Three
key configurations, 71, 56, and 36 key, programmable for
custom functions. Stackable sales, high, low prices and lookups
for 99 products/departments. Handles credit, debit, proprietary
cards. Options: Standalone receipt printer, PIN pad, cash
drawer, customer display.
CRT Terminal and Printer
Provides communication capability with the Islander. Can be
used to log system activity and enter and extract information.
Cables are not included with the terminal and must be ordered
separately.
LINK MC5 CRT Terminal (GASBOY P/N C03813)
Interface Modes: EIA RS-232 C Main and Auxiliary Ports,
IBM-compatible Centronics 25-pin interface, 50-38.4K Baud.
Power: 110/220 VAC, 50/60 HZ Keyboard: Low profile,
Extended PC (EPC) layout Display: 14" diagonal, 24, 25 or 43
scrollable lines, 80 or 132 columns. Data Transmission:
Asynchronous, Full Duplex. Includes CRT-Printer adapter
DB9F-DB25F
Okidata 184 Serial Printer (GASBOY P/N C03814)
Interface modes: RS-232C Power: 120 VAC, 220/240 VAC
Print speed: 155 cps, utility; 186 cps @10 and 17.1 cpi; 232 cps
@ 12 cpi, draft; 40 cps, NLQ. Data Transmission:
Asynchronous full duplex
RS-485 Junction Box
Provides a means for hard-wire connections and incorporates
protection circuitry to prevent electrostatic surges (which may
occur on the field wiring) from reaching the Islander.
Power Conditioner
Provides clean power to the Islander. Provides transient and
common mode protection.
Pump Control Units
Required for mechanical pumps and some electronic pumps.
Microprocessor controlled. One unit controls up to four fueling
positions (up to 8 fueling positions in self-contained unit) to a
maximum of 32. Certain applications may require peripheral
pump control units. Battery-backup, three solid state relays for
each pump/dispenser, manual override switches. Wall-mounted
or accommodated in island reader pedestal.
Electronic Pump/Dispenser Interfaces
Certain pump interfaces use controller boxes or special interface
devices. When installing any electronic pumps or registers,
follow the manufacturer's specifications. GASBOY 9800 Series
electronic pumps and dispensers can be connected to the
Islander via the RS-485 data loop. A Current Loop interface is
available from GASBOY and is required for Gilbarco electronic
pumps. For Islander II, Tokheim and Wayne use a controller
box to control the pumps. The CFN system interfaces with this
control box.
COMPONENT LOCATION
Careful planning for the layout of the site will help eliminate
possible problems with the start-up of the CFN system and will
ensure continued, reliable system operation.
Console
Location: Office environment, or at minimum, within a
protective enclosure.
Environment: 4ºF to 104ºF. 5% to 95% relative humidity, non-
condensing.
Dimensions: 7"H x 15-1/2"W x 18"D
Installation: Can be located up to 1000 feet away from Islander.
RS-485 junction box must be within 8 feet of console.
CRT Terminal/Printer:
Location: Clean office; a dirty location may cause premature
failure.
Environment: 32ºF to 104ºF, 10% to 95% relative humidity,
non-condensing, if supplied by GASBOY.
Dimensions: CRT: 12.5"H x 13.3"W x 12.2"D Weight:
Terminal: 20 lbs, Keyboard: 3 lbs. Printer: 3.2"H x 14.2"W x
10.8"D Weight: 9.9 lbs.
Installation: Do not install over a hazardous location.
External Modem
Location: Office environment, or at minimum, within a
protective enclosure.
Environment: 32ºF to 104ºF, if supplied by GASBOY.
Installation: Do not install over a hazardous location.
Islander or Satellite Islanders
Location: On fueling island.
Environment: -40ºF to 104ºF. 2% to 99% relative humidity,
non-condensing.
Dimensions: Blank Post: 58-1/2"H x 11-3/4"W x 11-1/2"D
Receipt Printer Post: 58-1/2"H x 12-3/4"W x 11-5/8"D
Installation: Provide adequate clearance to allow easy access to
post's access covers. If equipped with a receipt printer or
pedestal pump control unit, minimum 18 inches between post
and pumps/dispensers.