AMETEK XEL Series 60V and below User Manual
Xel series
This manual is related to the following products:
Table of contents
Document Outline
- Table of Contents
- Introduction
- Specification
- Safety
- Installation
- Connections
- Manual Operation
- Switching On and Power-On Conditions
- Output Control
- Setting Up the Output
- Constant Voltage
- Constant Current
- Instantaneous Current Output
- Current Meter Averaging
- Efficiency
- Connection to the Load
- Remote Sensing
- Output Connection and Remote Sensing on Programmable Models
- Series or Parallel Connection with Other Outputs
- Protection
- Over-temperature Protection
- View Settings
- Lock Settings
- Using Voltage Span
- Mode Control of the Quad-Mode Dual
- Remote Analog Control (Single programmable models only)
- Remote Interface Operation
- GPIB Interface
- Remote Commands
- RS232/USB Remote Command Format
- GPIB Remote Command Formats
- Command List
- Calibration
- Maintenance
- Sécurité
- Installation
- Connexions
- Connexions du panneau avant
- Connexions du panneau arrière
- Fonctionnement manuel
- Contrôle de la sortie
- Configuration de la sortie
- Tension continue
- Courant continu
- Sortie d’intensité instantanée
- Moyenne actuelle du mètre
- Économie
- Connexion à la charge
- Détection à distance
- Connexion de sortie et détection à distance sur
- Connexion en Série ou en Parallèle avec d’Autres
- Protection
- Protection contre les dépassements de températur
- Affichage des paramètres
- Verrouillage des paramètres
- Utilisation de l'écart de tension
- Mode Control (Controle de mode) du Quad-Mode Dual
- Commande Analogique Distante\(Modèles program
- Fonctionnement de l’Interface Distante
- Interface GPIB
- Commandes à distance
- Formats des commandes à distance RS232/USB
- Formats de commande à distance GPIB
- Liste des commandes
- Liste des commandes
- Entretien
- Sicherheit
- Installation
- Anschlüsse
- Manueller Betrieb
- Ausgangsregelung
- Einrichten des Ausgangs
- Konstantspannung
- Konstantstrom
- Momentanstrom
- Mittelwerte der Stromstärkemessung
- Wirkungsgrad
- Anschluss der Last
- Fernfühlerfunktion
- Ausgangsklemmen und Fernfühlerfunktion bei progr
- Serielle oder Parallelschaltung mit anderen Spannungsquellen
- Schutzvorrichtungen
- Übertemperaturschutz
- Einstellungen für das Display
- Einstellungen für die Verriegelung
- Verwendung des Spannungsbereichs
- Betriebsarten des Doppelnetzgeräts \(Quad-Mode
- Analogfernsteuerung \(nur programmierbare Einzel
- Bedienung der Fernschnittstelle
- GPIB-Schnittstelle
- Fernbedienungsbefehle
- RS232/USB-Fernbedienungsformate
- GPIB Fernbedienungsformate
- Befehlsliste
- Wartung
- Sicurezza
- Installazione
- Connessioni
- Connessioni del pannello frontale
- Connessioni del pannello posteriore
- Operatività manuale
- Controllo uscita
- Impostazione dell’uscita
- Tensione costante
- Corrente costante
- Uscita di corrente istantanea
- Media di misurazione di corrente
- Rendimento
- Connessione al carico
- Sensori remoti
- Connessioni di uscita e rilevamento remoto sui modelli programmabili
- Connessioni parallele e in serie con altre uscite
- Protezione
- Protezione da sovratemperatura
- Impostazioni di Visualizzazione
- Impostazioni di Blocco
- Utilizzo dell’ampiezza di tensione
- Controllo modalità del Dual Quad mode
- Indipendente
- Rilevamento isolato
- Rilevamento del rapporto (%) isolato
- Parallelo
- Impostazioni slave mantenute
- Controllo on/off uscita simultaneo
- Controllo analogico remoto (Solo modelli programmabili singoli)
- Operatività con l’interfaccia remota
- Blocco di un’interfaccia
- Selezione dell’indirizzo
- Operatività remota/locale
- Interfaccia RS232
- Interfaccia USB
- LAN
- Interfaccia GBIP
- Rapporti di stato
- Standard Event Status Register e Standard Event Status Enable Register (registro stati eventi ordinari e registro abilitazione stati eventi ordinari)
- Registro degli errori di esecuzione
- Limit Event Status Register e Limit Event Status Enable Register
- Status Byte Register e Service Request Enable Register
- Accensione e impostazioni predefinite per l’opera
- Comandi remoti
- RS232/USB Formati dei comandi remoti
- Manutenzione
- Seguridad
- Instalación
- Conexiones
- Conexiones del panel frontal
- Conexiones del panel posterior
- Funcionamiento manual
- Control de la salida
- Voltaje constante
- Corriente constante
- Salida de corriente instantánea
- Promediado del contador de corriente
- Eficacia
- Conexión a la Carga
- Detección remota
- Conexión de salida y detección remota en modelos
- Conexión en serie o paralelo con otras salidas
- Protección
- Protección de sobretemperatura
- Ajustes de visualización
- Ajustes del bloqueo
- Uso de la amplitud de voltaje
- Control de modo del doble del modo cuádruple
- Control analógico remoto\(modelos programable
- Funcionamiento remoto vía interfaz
- Interfaz GPIB
- Comandos Remotos
- Formado de los comandos remotos
- Lista de Comandos
- Mantenimiento
- Warranty Information