Basic drill press operation, Protection: eyes, hands, face, ears and body, Do not wear – Sears 113.21308 User Manual
Page 19: Loose clothing, Jewelry, Do tie back long hair, Installing drills
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

basic drill press operation
Follow the following instructions for operating your drill
press to get the best results and to minimize the likeli
hood of personal injury,
WARNING:
FOR YOUR OWN SAFETY, ALWAYS
OBSERVE THE SAFETY PRECAUTIONS HERE AND
ON PAGES 2, 3, AND 4.
1. Protection: Eyes, Hands, Face, Ears and Body
WARNING: TO AVOID BEING PULLED INTO
THE SPINNING TOOL -
1. Do NOT wear:
— gloves
— necktie
— loose clothing
— jewelry
2. Do tie back long hair
a. If any part of your drill press is missing, malfunc
tioning, has been damaged or broken . . . such
as the motor switch, or other operating control,
a safety device or the power cord , , . cease
operating immediately until the particular part
is properly repaired or replaced,
b. Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece should unexpectedly shift or
your hand should slip.
c. To avoid injury from parts thrown by the spring,
follow instructions exactly as given and shown
in adjusting spring tension of quill.
d. To prevent the workpiece from being torn from
your hands, spinning of the tool, shattering the
tool or being thrown, always properly support
your work so it won’t shift or bind on the tool:
—
Always position BACKUP MATERIAL (use
beneath the workpiece) to contact the left
side of the column.
—
Whenever possible, position the WORK
PIECE to contact the left side of the col
umn—if it is too short or the table is tilted,
clamp solidly to the table. Use table slots or
clamping ledge around the outside edge of
the table.
— When using a drill press VICE, always fasten
it to a table.
—
Never do any work "FREE HAND" (hand
holding workpiece rather than supporting it
on the table), except when polishing.
— Securely lock Head and Support to Column.
Table Arm to support, and Table to Table
Arm before operating drill press.
— Never move the Head or Table while the
tool is running.
— Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration.
— if a workpiece overhangs the table such that
it will fall or tip if not held, clamp it to the
table or provide auxiliary support.
—
Use fixtures for unusual operations to
adequately hold, guide and position work
piece.
—
Use the SPINDLE SPEED recommended
for the specific operation and workpiece ma
terial-check the panel Inside the guard
cover fo" drilling information; for acces
sories, refer to the instructions provided with
the accessories.
f. Never climb on the drill press Table, it could
break or pull the entire drill press down on you,
g. Turn the motor Switch Off and put away the
Switch Key when leaving the drill press.
h. To avoid injury from thrown work or tool contact,
do NOT perform layout, assembly, or setup
work on the table while the cutting tool is rotat
ing.
_
_
Use only accessories designed for this drill
press to avoid serious injury from thrown bro
ken parts or work pieces.
a. Holesaws must
NEVER be operated on this drill
press at a speed greater than 400 RPM.
b. Drum
Sanders must NEVER be operated on
this drill press at a speed greater than 1800
RPM.
c. Do not install or use any drill that exceeds 7" in
length or extends 6" below the chuck jaws. They
can suddenly bend outward or break.
d. Do not use wire wheels, router bits, shaper cut
ters, circle (fly) cutters or rotary planers on the
drill press.
ifi
^ «=
Q- o
O
o
‘m
CQ
CD
«5
§.
o
INSTALLING DRILLS
Insert drill into chuck far enough to obtain maximum
GRIPPING of the CHUCK JAWS ... the jaws are
approx. 1" long. When using a small drill do not insert
it so far that the jaws touch the flutes (spiral grooves)
of the drill.
Make sure that the drill is CENTERED in the chuck
before tightening the chuck with the key.
Tighten the drill sufficiently, so that it does not SLIP
while drilling.
Turn the chuck key clockwise to tighten-coun-
terciockwise to loosen.
19
a
o>