Novak Atom and Cyclone ESC User Manual
Page 27
CYCLONE & ATOM INSTRUCTION MANUAL
27
Other causes:
• ESC is not set—Repeat One-Touch Set-Up process.
• Check wiring and connections. Check operation of system
without ESC.
Receiver Glitches/Throttle Stutters During Acceleration
• Motor capacitors broken or missing—Refer to STEP 3.
• Receiver or antenna too close to speed control, power wires,
battery, or motor—Refer to STEP 2.
• Bad connections—Check wiring and connectors.
• Excessive current to motor—Use a milder motor or smaller
pinion gear.
• Motor brushes worn—Replace brushes. As motor brushes
wear, excessive motor noise will be generated. The motor
commutator may need to be cleaned or trued to help the
motor run more efficiently.
• Internal Polar Drive Capacitor is blown—Refer to Service
Procedures.
ESC Is Melted Or Burnt/ESC Runs With Switch Off
• Internal damage—Refer to Service Procedures.
Trouble-Shooting Guide (continued)
See also other documents in the category Novak For the car:
- Brushless Speed Control: Crusher Basic Set-Up (original) (55-1833-1 Rev.2) (2 pages)
- Brushless Speed Control: Crusher Basic Set-Up (w/Simple-Tuner) (55-1834-1 Rev.1) (2 pages)
- Brushless Speed Control: Crusher Field Guide (Crawler Mode) --- Simple-Tuner Version ESC (4) (4 pages)
- Brushless Speed Control: Crusher Field Guide (Standard Modes) --- Simple-Tuner Version ESC (1) (4 pages)
- Brushless Speed Control: Crusher Field Guide -- Original Version (55-1833P-1 Rev.2) (4 pages)
- Brushless Speed Control: Crusher Simple-Tuner Profile Cheat Sheet (14) (1 page)
- Brushless Speed Control: Drift Spec Basic Set-Up (55-3074-1 Rev.1) (2 pages)
- Brushless Speed Control: Drift Spec Track Guide (55-3074P-1 Rev.1) (2 pages)
- Brushless Speed Control: Edge 2S (55-1851-1 Rev.2) (2 pages)
- Brushless Speed Control: Edge Programming Guide (55-1851P-1.7 Rev.7) (2 pages)
- Brushless Speed Control: GTB 3 Basic Set-Up (55-1747-1.2) (2 pages)
- Brushless Speed Control: GTB 3 Track Guide (55-1747P-1.1) (4 pages)
- Brushless Speed Control: Impact Basic Set-Up (55-1730-1 Rev.3) (2 pages)
- Brushless Speed Control: Impact Track Guide (55-1730P-1 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Basic Set-Up (55-1756-2 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Track guide (55-1755P-2 Rev.1) (2 pages)
- Brushless Speed Control: Super-Tuner Brain Board Upgrade Track Guide (55-1746P-1 Rev.2) (2 pages)
- Brushless Speed Control: Timbuk2 Basic Set-Up (55-1832-1 Rev.4) (2 pages)
- Brushless Speed Control: Timbuk2 Field Guide (55-1832P-1 Rev.5) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Basic Set-Up Guide (55-1835-1 Rev.6) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Field Guide-- NEW version ESCs (standard height heat sinks) (55-1835P-1.4) (4 pages)
- Brushed Speed Control: Eiger & Eiger Pro -- V1 (low profile heat sinks) (55-1835-1.2) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide (55-1846-1.3) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide- 4 Profile Model (55-1846-1.4) (2 pages)
- Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) (4 pages)
- Brushed Speed Control: M2 Dig Field Guide- 4 Profile Model (55-1846P-1 Rev. 1.2) (4 pages)
- Brushless Motor: 4PHD Heavy-Duty 4-Pole BL Motor (55-3510M-1 Rev.1) (2 pages)
- Brushless Motor: 55-5980-1.C__Manufacturing 3-Up Layout (2 pages)
- Brushless Motor: 55-5984-1.D__Manufacturing 6-Up Layout (55-5984-1.D) (2 pages)
- Brushless Motor: 55-6801-1.D__Manufacturing 6-Up Layout (55-6801-1.D) (2 pages)
- Brushless Motor: Ballistic 540/550 Motor (2 pages)
- Brushless Motor: Brushless Motor Rotor and End Bell/Bearing Replacement (2 pages)
- Brushless Motor: Brushless Motor Stator Replacement (55-6801-1.D) (1 page)
- Brushless Motor: Brushless Motor Timing/Sensor Assembly Replacement (55-5984-1.D) (1 page)
- Brushless Motor: Brushless Sensor Harness Removal & Replacement (55-535X-1) (1 page)
- Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.1) (2 pages)
- Brushless Motor: Vulcan Motor (55-3640-1 Rev.3) (2 pages)
- Brushed Motor: Rock Star Motor (55-3557-1 Rev.C) (2 pages)
- Brushed Motor: Terra Claw Motor (55-3556-1 Rev.C) (2 pages)
- 1S LiPo Booster Module (1 page)
- 4PHD Motor Replacement Part (55-5956-1) (2 pages)
- 5463 3A High-Voltage BEC (55-5463-7) (2 pages)
- 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) (1 page)
- 55-583X-1.2_Manufacturing 6-Up Layout (55-583X-1.2) (1 page)
- 55-5860-1.2_Manufacturing 9-Up Layout (55-5860-1.2) (1 page)