Step 6: throttle profile selection – Novak Atom and Cyclone ESC User Manual
Page 19
CYCLONE & ATOM INSTRUCTION MANUAL
19
NOTE: These three profiles are not exclusive to the listed applications.
Experiment with all three profiles and see which works best for your
particular use.
Before beginning this step, the ESC should be connected to
the receiver and to a charged battery pack (4-10 cells for the
Cyclone; 4-6 cells for the Atom).
1. TURN ON THE TRANSMITTER
2. TURN ON THE SPEED CONTROL
3. PRESS AND HOLD THE ESC'S 1-TOUCH BUTTON until
the status LED turns solid green (approximately six
seconds). The LED will first turn red. A few seconds later it
will turn solid green.
4. RELEASE THE 1-TOUCH BUTTON and approximately one
second later, the status LED will blink red. The number of
times the LED blinks indicates the profile number selected.
For example if the status LED blinks red twice after the
button is released, then profile 2 is selected, and so forth.
Since drivers have their own
racing preferences, the Cyclone &
Atom are factory-programmed
with three user-selectable
profiles to choose from. This
chart describes them.
Continued
STEP 6: THROTTLE PROFILE SELECTION
Dead Band
Brake Frequency
Drive Frequency
Minimum Drive
PROFILE
Measurement Units
%
%
KHz
KHz
1 Stock
6
6.0
3.90
5.86
2 Drag Brake
6
6.0
5.86
7.80
3 Modified
4
1.5
3.90
15.60
- Brushless Speed Control: Crusher Basic Set-Up (original) (55-1833-1 Rev.2) (2 pages)
- Brushless Speed Control: Crusher Basic Set-Up (w/Simple-Tuner) (55-1834-1 Rev.1) (2 pages)
- Brushless Speed Control: Crusher Field Guide (Crawler Mode) --- Simple-Tuner Version ESC (4) (4 pages)
- Brushless Speed Control: Crusher Field Guide (Standard Modes) --- Simple-Tuner Version ESC (1) (4 pages)
- Brushless Speed Control: Crusher Field Guide -- Original Version (55-1833P-1 Rev.2) (4 pages)
- Brushless Speed Control: Crusher Simple-Tuner Profile Cheat Sheet (14) (1 page)
- Brushless Speed Control: Drift Spec Basic Set-Up (55-3074-1 Rev.1) (2 pages)
- Brushless Speed Control: Drift Spec Track Guide (55-3074P-1 Rev.1) (2 pages)
- Brushless Speed Control: Edge 2S (55-1851-1 Rev.2) (2 pages)
- Brushless Speed Control: Edge Programming Guide (55-1851P-1.7 Rev.7) (2 pages)
- Brushless Speed Control: GTB 3 Basic Set-Up (55-1747-1.2) (2 pages)
- Brushless Speed Control: GTB 3 Track Guide (55-1747P-1.1) (4 pages)
- Brushless Speed Control: Impact Basic Set-Up (55-1730-1 Rev.3) (2 pages)
- Brushless Speed Control: Impact Track Guide (55-1730P-1 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Basic Set-Up (55-1756-2 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Track guide (55-1755P-2 Rev.1) (2 pages)
- Brushless Speed Control: Super-Tuner Brain Board Upgrade Track Guide (55-1746P-1 Rev.2) (2 pages)
- Brushless Speed Control: Timbuk2 Basic Set-Up (55-1832-1 Rev.4) (2 pages)
- Brushless Speed Control: Timbuk2 Field Guide (55-1832P-1 Rev.5) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Basic Set-Up Guide (55-1835-1 Rev.6) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Field Guide-- NEW version ESCs (standard height heat sinks) (55-1835P-1.4) (4 pages)
- Brushed Speed Control: Eiger & Eiger Pro -- V1 (low profile heat sinks) (55-1835-1.2) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide (55-1846-1.3) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide- 4 Profile Model (55-1846-1.4) (2 pages)
- Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) (4 pages)
- Brushed Speed Control: M2 Dig Field Guide- 4 Profile Model (55-1846P-1 Rev. 1.2) (4 pages)
- Brushless Motor: 4PHD Heavy-Duty 4-Pole BL Motor (55-3510M-1 Rev.1) (2 pages)
- Brushless Motor: 55-5980-1.C__Manufacturing 3-Up Layout (2 pages)
- Brushless Motor: 55-5984-1.D__Manufacturing 6-Up Layout (55-5984-1.D) (2 pages)
- Brushless Motor: 55-6801-1.D__Manufacturing 6-Up Layout (55-6801-1.D) (2 pages)
- Brushless Motor: Ballistic 540/550 Motor (2 pages)
- Brushless Motor: Brushless Motor Rotor and End Bell/Bearing Replacement (2 pages)
- Brushless Motor: Brushless Motor Stator Replacement (55-6801-1.D) (1 page)
- Brushless Motor: Brushless Motor Timing/Sensor Assembly Replacement (55-5984-1.D) (1 page)
- Brushless Motor: Brushless Sensor Harness Removal & Replacement (55-535X-1) (1 page)
- Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.1) (2 pages)
- Brushless Motor: Vulcan Motor (55-3640-1 Rev.3) (2 pages)
- Brushed Motor: Rock Star Motor (55-3557-1 Rev.C) (2 pages)
- Brushed Motor: Terra Claw Motor (55-3556-1 Rev.C) (2 pages)
- 1S LiPo Booster Module (1 page)
- 4PHD Motor Replacement Part (55-5956-1) (2 pages)
- 5463 3A High-Voltage BEC (55-5463-7) (2 pages)
- 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) (1 page)
- 55-583X-1.2_Manufacturing 6-Up Layout (55-583X-1.2) (1 page)
- 55-5860-1.2_Manufacturing 9-Up Layout (55-5860-1.2) (1 page)