Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) User Manual

Novak power connectors

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

NOVAK POWER CONNECTORS

Low-Loss • Polarized • Gold-Plated

For best results, strip, twist, & pre-tin about 1/4” of your

16-12G power wires before soldering to the connector.

To avoid over-heating connector’s plastic, plug into a mating/opposite-

end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel

of the connector (“+” & “–” are marked on the side of connector). Heat

the tinned wire end with a good quality, high-power soldering iron

until the solder reflows into the connector’s barrel forming a clean

and continuous solder joint. If needed, add a small amount of extra

solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over

the connector’s exposed barrel and the solder joint.

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

www.teamnovak.com