beautypg.com

Novak Brushless Speed Control: Crusher Simple-Tuner Profile Cheat Sheet (14) User Manual

Throttle profile cheat sheet, Profile 1, Profile 4 profile 3

background image

1

2

3

4

5

6

7

8

9

10

1 Profile Select

x

x

x

1

2

3

4

2 Drag Brake (%)

x

OFF

3

6

9

15

20

25

30

40

50

3 Min Brake (%)

x

0

3

6

9

12

15

18

20

30

45

4 Brake Freq (KHz)

x

1.5

2

2.2

2.5

3

3.5

4.5

6

7

8

5 Timing (degree)

x

0

10

15

18

20

25

28

30

33

35

6 Timing RPM

x

Low

2

3

4

5

6

7

8

9

High

7 Brake Power (KHz)

x

x

10

20

30

40

50

60

70

80

90

100

8 Dead Band (%)

x

x

2

3

4

5

8

9 Drive Freq (KHz)

x

x

8

10

12

14

16

21

23

26

32

36

10 Min Drivev(%)

x

x

0

1

2

3

4

6

8

10

12

15

11 Reverse

x

x x

OFF

ON

12 Motor Rotation

x

x

x

CCW

CW

13 Voltage Cut-Off

x

x

x

OFF

ON

14 Data Reset

x

x

NO

YES

15 Sensor Test

A B C

1

2

3

4

5

6

7

8

9

10

1 Profile Select

x

x

x

1

2

3

4

2 Drag Brake (%)

x

OFF

3

6

9

15

20

25

30

40

50

3 Min Brake (%)

x

0

3

6

9

12

15

18

20

30

45

4 Brake Freq (KHz)

x

1.5

2

2.2

2.5

3

3.5

4.5

6

7

8

5 Timing (degree)

x

0

10

15

18

20

25

28

30

33

35

6 Timing RPM

x

Low

2

3

4

5

6

7

8

9

High

7 Brake Power (KHz)

x

x

10

20

30

40

50

60

70

80

90

100

8 Dead Band (%)

x

x

2

3

4

5

8

9 Drive Freq (KHz)

x

x

8

10

12

14

16

21

23

26

32

36

10 Min Drivev(%)

x

x

0

1

2

3

4

6

8

10

12

15

11 Reverse

x

x

x

OFF

ON

12 Motor Rotation

x

x

x

CCW

CW

13 Voltage Cut-Off

x

x

x

OFF

ON

14 Data Reset

x

x

NO

YES

15 Sensor Test

A B C

1

2

3

4

5

6

7

8

9

10

1 Profile Select

x

x

x

1

2

3

4

2 Drag Brake (%)

x

OFF

3

6

9

15

20

25

30

40

50

3 Min Brake (%)

x

0

3

6

9

12

15

18

20

30

45

SLIDE THE ESC’s ON/OFF SWITCH TO ‘ON’ POSITION

4 Brake Freq (KHz)

x

1.5

2

2.2

2.5

3

3.5

4.5

6

7

8

5 Timing (degree)

x

0

10

15

18

20

25

28

30

33

35

6 Timing RPM

x

Low

2

3

4

5

6

7

8

9

High

7 Brake Power (KHz)

x

x

10

20

30

40

50

60

70

80

90

100

8 Dead Band (%)

x

x

2

3

4

5

8

9 Drive Freq (KHz)

x

x

8

10

12

14

16

21

23

26

32

36

10 Min Drivev(%)

x

x

0

1

2

3

4

6

8

10

12

15

11 Reverse

x

x

x

OFF

ON

12 Motor Rotation

x

x

x

CCW

CW

13 Voltage Cut-Off

x

x

x

OFF

ON

14 Data Reset

x

x

NO

YES

15 Sensor Test

A B C

1

2

3

4

5

6

7

8

9

10

1

Hill/Hold/Drag Brake

x

OFF

20

45

75

95

P1

P2

P3

P4

P5

2

Brake Freq (KHz)

x

1.5

2

2.2

2.5

3

3.5

4.5

6

7

8

3

Rock Boost

x

OFF

ON

4

Dead Band (%)

x

x

2

3

4

5

8

5

Drive Freq (KHz)

x

x

8

10

12

14

16

21

23

26

32

36

6

Min Drivev(%)

x

x

0

1

2

3

4

6

8

10

12

15

7

Motor Rotation

x

x

x

CCW

CW

8

Voltage Cut-Off

x

x

x

OFF

ON

9

Data Reset

x

x

NO

YES

10

Sensor Test

A B C

1 CONNECT THE ESC TO A FULLY CHARGED BATTERY

PACK, A RECIEVER, AND THE MOTOR’S SENSOR
HARNESS

2

WWW.TEAMNOVAK.COM

© 2014 NOVAK R/C, INC. All Rights Reserved Printed 6-17-14

PROFILE 1

BASHING

LED COLOR >

Standard operation with reverse disabled, timing

values active, and low power brakes. Doing a little

speed run testing, you can use this profile to save a

little time and start out safe.

540 / 550 (2S-3S) / 4-Pole Motor Compatible.

# LED BLINKS

# LED BLINKS

PROFILE 4

PROFILE 3

Standard operation with reverse.

Recommended for 4x4 SCT / Bashing.

540 / 550 / 4-Pole Motor Compatible.

Standard operation with reverse disabled.

Defaults set with no timing for “blinky” mode racing.

Great starting profile for club and spec racing.

540 / 550 / 4-Pole Motor Compatible.

RACING

PROFILE 2

# LED BLINKS

LED COLOR >

LED COLOR >

TIMING TEST

crawling

4

WITH ESC AT NEUTRAL, PRESS & HOLD SET
BUTTON.
Release ESC’s SET button once LEDs are lit for the
desired setting;To skip a parameter, continue to press &
hold SET button until desired parameter is reached.

PRESS & HOLD SET BUTTON TO STORE NEW
SELECTION
When SET button is pressed & held for about 1 second,
new selection is stored in ESC’s memory—Status LEDs
will scroll to indicate ESC is exiting programming & ESC
returns to neutral.

3

# LED BLINKS

LED COLOR >

TO CHANGE PARAMETER SETTINGS:

SENSOR TEST: Release button and rotate motor to confirm

sensor operation. Blue/Amber/Red LED will blink as you rotate

the motor pinion shaft.

THROTTLE PROFILE

CHEAT SHEET

Auto-detects Novak Crawling brushless motor. This

mode features Novak's Hill/Hold/Drag Brakes

(Parameter #1 with Power Hill Settings P1-P5), Rock

Boost (Parameter #3; for 2S only), and instant reverse.

There is no time constraint during selection of custom

parameters.

5

SELECT PARAMETER VALUE
LED flashes to indicate active setting (refer to table).
Quick press & release SET button to select desired
setting.

Default settings for each profile highlighted in
orange. Perform One-Touch Set-Up prior to
customization (refer to instructions).

For explanation of programming parameters,
refer to the Crusher Field Guide (available in the
DOWNLOADS section of the Novak website
www.teamnovak.com/downloads). There is a
Field Guide for Standard Modes of operation
(Profiles 1-3) and Crawling Mode.

To revert to the default settings, select

#14 (#9 in the Crawling Profile) parameter

DATA RESET and select two blinks.