Great Planes 38% Extra 330S ARF - GPMA1290 - Manual (Page 4)

Other Radio Gear
The following servo extensions were used on the model in
the instruction manual:
Note: If using digital servos, be certain to use servo
extensions suitable for use with digital servos. The servo
extensions listed below are suitable for both analog and
digital servos.
❏
(2) 6" [150mm] heavy-duty dual servo extension (coming
from the receiver inside the fuselage for ailerons –
FUTM4134 for Futaba)
❏
(2) 6" [150mm] Pro HD servo extensions (1-throttle servo,
1-servo synchronizer for rudder servos – HCAM2701 for
Futaba)
❏
(2) 12" [305mm] Pro HD servo extensions (for inboard
aileron servos – HCAM2711 for Futaba)
❏
(2) 36" [915mm] Pro HD servo extensions (for outboard
aileron servos -- HCAM726 for Futaba)
❏
A servo synchronizer for the three rudder servos is also
required (Such as MSA-10 used for Futaba servos –
FUTM4155)
If connecting the elevator servos to separate channels in
the receiver (and using the mixing in the transmitter) the
following servo extensions will also be required:
❏
(2) 6" [150mm] Pro HD servo extensions (HCAM2701
for Futaba)
❏
(2) 12" [305mm] Pro HD servo extensions (HCAM2711
for Futaba)
❏
(2) 36" [915mm] Pro HD servo extensions (HCAM2726
for Futaba)
If connecting the elevator servos to the same channel in
the receiver, a servo reverser and (2) 36" [915mm] servo
extensions will be required:
❏
(1) servo reverser (such as Futaba SR-10 – FUTM4150)
❏
(2) 36" [915mm] Pro HD servo extension (HCAM2726 for
Futaba)
These switches and charge receptacles were also used:
❏
(2) Heavy-duty on/off switches (1-ignition battery, 1-
radio system such as Hobbico HD switch for Futaba J
(HCAM2761)
❏
(2) Ernst Charge Receptacles (ERNM3001 for Futaba)
Hardware and Accessories
In addition to typical hobby tools, following is the rest of the
hardware and accessories used to fi nish the Extra 330S
ARF:
❏
Pro ™ 30-minute epoxy (GPMR6047)
❏
1 oz. [30g] Medium Pro CA+ (GPMR6008)
❏
CA applicator tips (HCAR3780)
❏
Threadlocker thread locking cement (GPMR6060)
❏
(2 pkgs) 3' Du-Bro 1/8" Tygon fuel tubing (DUBQ0493)
❏
1/4" [6.5mm] R/C foam rubber (HCAQ1000)
❏
1/8" single-sided foam tape (GPMQ4424)
❏
Silver solder w/fl ux (GPMR8070)
Covering Tools
A Top Flite ® or 21st Century ® model airplane covering iron with
a protective covering sock may be necessary for tightening
any covering on the model that may have loosened or formed
wrinkles between the time of production and your purchase.
The 21st Century iron is preferred as it has a longer cord and
a rounded, contoured shoe. A trim iron is not as much of a
necessity, but would still be very handy for sealing the edges
down inside servo openings and other small areas.
❏
21st Century sealing iron (COVR2700)
❏
21st Century iron cover (COVR2702)
❏
21st Century trim seal iron (COVR2750)
❏
Top Flite MonoKote ® sealing iron (TOPR2100)
❏
Top Flite Hot Sock ™ iron cover (TOPR2175)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
KIT INSPECTION
Before starting to build, inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not of
acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or
missing parts, use the part names exactly as they are written
in the Kit Contents list.
Great Planes Product Support
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970, ext. 5
Fax: (217) 398-7721
E-mail: [email protected]
4