RCA VR725HF - Manual (Page 13)

Setting Up the VCR
Startup
5. Place channels in the VCR’s memory.
The first time you turn on the VCR or after a power
interruption, the VCR displays a message on the TV
screen prompting you to perform an AUTO CHANNEL
SEARCH. If the message does not appear, go to step A
below. If the message appears, follow the directions on
the screen.
Wait until the channel numbers stop changing. This
takes about one to two minutes. Then, the TV tunes to
the lowest channel found. Pressing CHAN up or down
selects only the active channels.
If you ever need to manually SETUP CHANNELS on
the VCR because you change cable or antenna signals:
A. Press MENU»PROG to display the VCR MAIN
MENU on the TV screen. If this menu does not
appear:
• Make sure TV is tuned to the same channel as
the 3 CH. 4 switch on the VCR or the TV's video
input (refer to the TV's manual).
• Press VCR1, then press MENU»PROG again.
• If you are using a basic hookup, the VCR
indicator should be on. If it is not on, press
TV»VCR to turn it on.
• Check the connections.
B. Press 4 to display the CHANNELS menu.
C. Press 1 to begin AUTO CHANNEL SEARCH.
The VCR automatically selects CABLE (cable TV) or
ANTENNA. If you need to change the setting
manually, press 3.
A U T O C H A N N E L S E A R C H
C O N N E C T A N T E N N A C A B L E . . .
T H E N P R E S S C H U P
V C R M A I N M E N U
V C R P L U S +
T I M E R R E C O R D I N G S
S E T C L O C K
C H A N N E L S
C H A N N E L S
1 A U T O C H A N N E L S E A R C H
2 A D D / R E M O V E C H A N N E L S
3 S I G N A L T Y P E : C A B L E
4 V C R P L U S + C H A N N E L L I S T
5 C A B L E / D S S B O X S E T U P
0 E X I T
6. Add or remove channels from the VCR’s memory.
You can add or remove channels if some of the
channels are not active, have weak signals, or if you do
not want to watch them.
We recommend channels be placed in memory using
the AUTO CHANNEL SEARCH feature described in
step 5 before adding or removing channels. Channels 2­
13, LI and L2 are present at the factory.
A. Press VCR1.
B. Press MENU«PROG on the remote to see the VCR
MAIN MENU on the TV screen.
C. Press 4 to display the CHANNELS menu.
D. Press 2 to display the ADD/REMOVE CHANNEL
menu.
E. Follow the directions on the screen.
F. You can add or remove more channels by entering
channel numbers or using CHAN up or down.
V C R M A I N M E N U
1 V C R P L U S +
2 T I M E R R E C O R D I N G S
3 S E T C L O C K
4 C H A N N E L S
C H A N N E L S
1 A U T O C H A N N E L S E A R C H
2 A D D / R E M O V E C H A N N E L S
A D D / R E M O V E C H A N N E L
C H A N N E L 0 3
I S P R E S E N T L Y A D D E D
P R E S S C L E A R T O R E M O V E
P R E S S M E N U T O E X I T
11