KEYENCE SJ-M300 - Manual (Page 12)

11
5-2 Specifications
This section provides the specifications of the SJ-M300 Series.
■ Static Elimination Bar/Controller Unit
*1: The following conditions were applied for measurement.
Please inquire for ion balance in operating distance 50mm (50 Hz) of a V,VC type separately.
*2: The effective length represents the operating area at an operating distance of 50 mm.
*3: The total length represents the length of the model with a mounting bracket attach.
■ AC adapter
* The power cable supplied with SJ-U2 is 125V rated power voltage.
Model
Static Elimination Bar
SJ-M030/030C/030G/
030V/030VC
SJ-M070/070C/070G/
070V/070VC
Controller Unit SJ-M300
Voltage application method Pulse AC
Applied voltage ±5.5 kV
Rated output voltage ±6 kV
Ion balance control method I.C.C. method
Ion balance *1 ±30 V
Air purge supply pressure 0.2 MPa max.
Control input Static elimination stop input No-voltage input
Control output
Alarm output
NPN open collector
100 mA 40 V or less
Ion level alarm output
Condition alarm output
Rating
Power voltage 24 VDC ±10%
Current consumption 450 mA max.
Environmental
resistance
Operating ambient
temperature
0 to +40°C
Operating ambient
humidity
35 to 65%RH, No condensation
Effective length *2 164 mm 324 mm
Total length *3 220 mm 380 mm
Weight
Static elimination bar Approx. 600 g Approx. 720 g
Controller Approx. 300 g
Model(Static
elimination bar)
SJ-M030/070 SJ-M030C/070C SJ-M030G/070G SJ-M030V/070V SJ-M030VC/070VC
Air purge None None
(3 NL/min)/
1 electrode (1 NL/min)/
1 electrode (1 NL/min)/
1 electrode
Downward air flow 0.3m/s
Operating distance 50mm(50Hz), 600mm(8Hz), 1500mm(1Hz)
Model SJ-U2
Rating
Rated input 100 to 240 VAC (50/60 Hz)
Rated output 24 VDC 2.65 A
Environmental resistance
Operating ambient temperature 0 to +35°C
Operating ambient humidity 20 to 80%, No condensation
Weight Approx. 250 g
5-3 External Dimensions
This section presents the external dimensions of the SJ-M Series.
■ Body
Static Elimination Bar
At the time of
front installation
46 (SJ-M030/030C/030G)
41 (SJ-M030V/030VC) 26.5
5.5
29 26
43 40 40
220
200
At the time of
side installation
(17.5)
Rc1/8 17.5
28.5 (SJ-M030/030C/030G)
23.5 (SJ-M030V/030VC)
(17.5)
240(P=40x6)
5.5
26.5
43
380
360
At the time of
side installation
Rc 1/8
46(SJ-M070/070C/070G)
41(SJ-M070V/070VC)
28.5(SJ-M070/070C/070G)
23.5(SJ-M070V/070VC)
17.5
29 26
At the time of
front installation
15 mm dia.
51 3
18
2-4.4 mm dia.(thru hole)
191
181 24
30
2.5
11.5 5 131 5 8.5
6 mm dia. cable length
300mm (min. bend radius 18) 10 mm dia.cable length 800mm
min. bend radius 30
35
5-3 External Dimensions
Controller Unit SJ-M300
Mounting Fixture detail
■ Extension cable (SJ-C3)
■ AC adapter (SJ-U2)
* For details of the AC cable, contact the KEYENCE sales office in your district.
50
120
5
70
32
76
46
36
89
37
26
13
hole for self-tapping
screw(2-M3)
(screw hole depth= 6mm)
5
4
28
18
18
11
4
27.5
17.5
29
6 mm dia.
cable length 3 m 49
15.5
51
15
(37.5)
7
ш16
(10.3)
(16.3)
(12.5) (14)
28
ш3.5
1800
114.5
50.5
1 Troubleshooting
This appendix describes trouble that may occur during use of the SJ-M Series and how to remedy this
trouble. Check the following table before sending in your SJ-M Series for repair.
Symptom Check Item Remedy
No indication on ion
monitor
Is the power cable connected
properly?
Connect the power cable correctly.
Is a power supply within specification
being used? Use a power supply that is within
specification.
Static elimination is
not performed.
Is the electrode probe worn or dirty?
Perform maintenance on the electrode probe
or replace the Electrode Unit.
Is static elimination stop currently
set? Cancel static elimination stop input on the SJ-
M Series.
Is the abnormal discharge detection
function operating? Check the Static Elimination Bar for any
conductive substances (e.g. oil droplets).
Static elimination is
not performed
properly. Are conductors or other Static
Eliminators located nearby the Static
Eliminator?
Move the Static Eliminator away from
conductors or other static eliminators nearby.
The ion level alarm is
output/indicated.
Is the electrode probe worn or dirty?
Perform maintenance on the electrode
probes or replace the Static Elimination Bar.
Are conductive objects located in the
surrounding area? Check the installation state.
"Locations"(page 5)
The condition alarm is
output/indicated.
Are static elimination target objects
having a very high charged level
located nearby the Static
Eliminators?
Increase the number of connected static
eliminators.
Is the electrode probe worn or dirty?
Perform maintenance on the electrode
probes or replace the Static Elimination Bar.
The alarm indicator
lights.
–
Check “During an alarm (levels 1, 2)”
(
page13) in this Instruction Manual.
Control output is not
output correctly.
Is output wired correctly?
Check the output circuit and wiring, and
connect correctly.
Static elimination stop
input is not input
correctly.
Is input wired correctly?
Check the input circuit and wiring, and
connect correctly.
Do not know meaning
of indicators.
–
Check "Table of Indicated States" ( page
12) in this Instruction Manual.