KEYENCE IL Series - Manual (Page 2)

2
Setup Functions
 Set the R.V. value to the Shift target value
1. Press the left/right arrow buttons until the sub display shows the
Shift target value.
2. Press the up/down arrow button to change the Shift target value.
3. Press the [ZERO SHIFT] button.
4. The current R.V. value would be set to the Shift target value.
 Set the HIGH and LO tolerance.
1. Press the left/right arrow buttons until the sub display shows the
HIGH/LOW limit setting value.
2. Input the HIGH or LO tolerance by pressing the up/down arrow
buttons.
3. The HIGH and LOW tolerance will be set.
 Setting the Key Lock
1. Press the [MODE] and the up (or down) arrow button for at least 2
seconds.
2. The Key Lock display would appear.
 Canceling the Key Lock
1. When the Key Lock is set, press the MODE and the up (or down)
arrow button for at least 2 seconds.
2. The Key Lock would be cancelled.
 Initializing the sensor
1. Press the SET button 5 times while
pressing the MODE button. The main
display will show “rESET”.
2. Select “YES” by pressing the up/down
arrow button, and press the [MODE]
button. The main display will show
“out”.
3. Select the output polarity from “NPN”
and “PNP” by pressing the up/down
arrow button, and press the [MODE]
button. The main display will show
“AnLG”.
4. Select the analog output from “oFF”,
“0-5V”, “-5-5V”, “1-5V” and “4-20mA” by
pressing the up/down arrow button, and
press the [MODE] button. The sensor
will be initialized.
 Changing the bank (program)
1. Press the up/down arrow button while pressing the [MODE] button.
2. The bank (program) would be switched to another one. Each bank
(program) will have an own HIGH limit setting value/LOW limit
setting value/Shift target value/Analog output upper and lower
range.
Basic setting mode
 How to enter the Basic setting mode
1. Press the [MODE] button for at least 2 seconds.
2. Press the [MODE] or left/right arrow button and select the function
number.
 01 Measurement direction
Set the measurement direction from [Normal] and [Reverse].
[Normal]: The value increases when the target comes close to the
sensor head.
[Reverse]: The value decreases when the target comes close to the
sensor head.
 02 Sampling rate
Set the measurement sampling rate.
 03 Average rate
Set the average rate. High-pass filter and Step count filter can be set
here.
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0 1 2 3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0 1 2 3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0 1 2 3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0 1 2 3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
GO
HOLD CALC CHECK
Shift target value
[SHIFT]
lights up.
HIGH tolerance value
[HI]
lights up.
LOW tolerance value
[LO]
lights up.
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
GO
HOLD CALC CHECK
Performing the initial reset
Output polarity
Analog output
Press ▼ while
holding down the
[MODE] button.
Press ▼ while holding
down the [MODE] button.
Press ▼ while holding
down the [MODE] button.
Press ▼ while holding
down the [MODE] button.
< While Bank 1 is selected>
< While Bank 2 is selected>
< While Bank 3 is selected>
BANK 0 lights
BANK 1 lights
BANK 2 lights
BANK 3 lights