KEYENCE FS-32C(P) - Manual (Page 5)

5
Display Setting Menu
System Setting Menu
Initializing, Saving and Loading the Settings
„ Initializing the settings
1
While pressing , press for 5 seconds or longer.
2
Select “ T5V “with the button, and press .
3
Select “ KPKV ” with the button, and press to initialize.
Default setting
Power mode: FINE
Detection mode: Normal
Setting value:
50
Output selection: L ON
„ Saving the settings
1
While pressing , press for 5 seconds or longer.
2
Select “ 5#X' ” with the button, and press .
3
Select “ ;'5 ” with the button, and press to save.
„ Loading the setting
1
While pressing , press for 5 seconds or longer.
2
Select “ T5V ” with the button, and press .
3
Select “ =X5V ” with the button, and press to load.
Back to A of
the basic setting.
DSC DSC
5
Light emission power selection
Select the setting by pressing the button.
Display
Power mode
FinE
Normal
Approx. 15% of the normal time
Approx. 3% of
the normal time
Turb/SuPr/
uLtr/MEGA
Approx. 1.5% of
the normal time
hSP
Approx. 11% of
the normal time
Press
MODE
Select the setting by pressing the button.
Not to be used.
Uses the display scaling function.
Uses the zero-shift function.
Display scaling target value setting
Configure setting by pressing the button.
The value can be set between 100 and
10000 in unit of 100.
10000 is displayed as FuLL.
When oFF or
ShFt is selected
When no is
selected
When SCAL
is selected
DSC
DSC
DSC
DSC
DSC
DSC
DSC
DSC
Select the setting by pressing the button.
Normal display
Reverses the display.
Even when the display is reversed,
the green light indicates setting values,
and the red light indicates received
light intensity.
Select the setting by pressing the button.
Does not customize the display.
Customizes the display.
Selectable display setting
The items shown left are displayed in
order every time the MODE button is
pressed. (see page 3)
Select the setting by pressing the
button.
Adds the item to the
selectable display.
Deletes the item from the
selectable display.
When no is
selected
Normal
Extension
Bar
Excess gain
(%)
6
Display value correction function selection
7
Display reverse selection
8
Display customization selection
(1)
(2)
(3)
(4)
Press
MODE
Press
MODE
Press
MODE
Press
MODE
.
.
.
.
.
.
.
.
.
From the basic menu
Back to A of
the basic setting.
DSC
DSC
DSC
HOLD
Power mode
HOLD
Excess gain
(%)
(5)
(7)
(6)
Press
MODE
Press
MODE
Press
MODE
When SCAL or
ShFt is selected
on page 4, No.4-C
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Press
MODE
When setting each mode, the display returns normal by pressing the
button for 3 seconds or longer.
Reference
MODE
Configure setting by pressing the button.
APC is enabled.
APC is disabled.
DSC
DSC
DSC
DSC
DSC
Configure setting by pressing the button.
Saves power (Turns off the display).
While the power save mode is
activated, only one segment on the
digital monitor remains displayed.
Normal display
Select the setting by pressing the button.
Normal
The number of units of interference
prevention is twice as many as in the
normal time. (The response time is also
twice as long as in the normal time.
The detection distance is the same
as in the normal time.)
Select the setting by pressing the button.
Level 1
Level 2
Level 3
9
S-APC setting
10
Power save mode setting
11
Key lock level setting (see page 6)
12
Selecting the number of units of interference prevention
.
.
.
.
.
.
.
.
.
About APC (Auto Power Control)
In normal cases, use the sensor with APC
disabled.
When APC is enabled, the light intensity is
monitored and corrected in order to maintain
regular light transmission. If the environment is
sufficiently clean, a highly accurate detection can
constantly be performed.
Note: Long-term use of APC imposes heavier
load on the LED than when disabled.
To turn all the displays OFF (both digital
monitor and operation status indicators)
ALL can be selected when is pressed for 3
seconds or longer while “on” is selected.
To restore the display from Display OFF, press
MODE and L/D ON buttons simultaneously for 3
seconds or longer.
From the basic menu
Back to A of
the basic setting.
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Press
MODE
L/D
ON SET
MODE
MODE
L/D
ON SET
MODE
MODE
L/D
ON
SET
MODE
MODE