Rice Lake 920i Installation Manual V1.05 - Manual (Page 84)

80 920i Installation Manual
DB.ALIAS
The DB.ALIAS command is used to get or set the alias
used by iRite programs to reference the speciÞed
database. Each database alias must be unique among
all databases and adhere to the following rules: 8
character maximum; must begin with an alpha
character or an underscore; can only contain AÐZ, aРz,
0Р9, or an underscore (_).
Example. The following command assigns an alias of
TRUCKS_2 to the Þrst database on the memory card
installed in slot 2:
DB.ALIAS.1#2=TRUCKS_2
Sending the DB.ALIAS command alone, without
assigned data, returns the current database alias.
DB.CLEAR
To clear the contents of a database, send the following
command:
DB.CLEAR.n#x
Where:
n is the database number within the memory card
x is the slot number of the memory card (0 is the
onboard memory)
The 920i responds with OK if the command is
successful, ?? if unsuccessful.
DB.DATA
The DB.DATA command can be used to send data to or
retrieve data from the 920i .
Data can be sent to the indicator using the following
command:
DB.DATA.n#x = data{ | }
Where:
n is the database number within the memory card
x is the slot number of the memory card (0 is the
onboard memory)
data represents a single cell of a row of data
{ | } is a pipe character (ASCII 124), used to
delimit cell data. If the data being sent is not the
last cell of the row, append the pipe character to
the data to indicate that more data is coming for
that particular row. If the data being sent is the last
cell of the row, do not append the pipe character.
If the command is accepted, the 920i responds with
OK ; if not, it responds with ??.
Example. The following commands place the data
shown in Table 9-13 into the Þrst database in the
onboard memory:
DB.DATA.1#0=this|
DB.DATA.1#0=is|
DB.DATA.1#0=a|
DB.DATA.1#0=test
DB.DATA.1#0=aaa|
DB.DATA.1#0=bbb|
DB.DATA.1#0=ccc|
DB.DATA.1#0=ddd
Sending the DB.DATA command alone, without
assigned data, returns the database contents:
DB.DATA.n#x
The 920i responds with the entire contents of the
database. Returned data is cell-delimited with the pipe
character (ASCII 124) and row-delimited with
carriage returns (ASCII 13).
For example, the following command could be used to
return the contents of database 1 in the onboard
memory:
DB.DATA.1#0
If the database contents are the records shown in
Table 9-13, the indicator responds with the following
data, using pipe characters and carriage returns to
delimit the database cells and rows, respectively:
t h i s | i s | a | t e s t < C R > a a a | b b b | c c c | d d d < C R >
NOTE: There is no end of database notification at the
end of the DB.DATA command transmission. Use a
receive time-out to determine command completion. This
time-out should vary based on baud rate.
You should determine the number of records currently
in the database both prior to and after sending the
DB.DATA command to verify that the correct number of
records are received. The number of records can be
determined with the
DB.SCHEMA command.
DB.SCHEMA
The DB.SCHEMA command is used to get or set the
structure of a database.
DB.SCHEMA.n#x
The 920i responds to the command above by returning
the following:
,,
,,,...
The , , and
elements repeat for each column in the database.
Record
Cell
1 2 3 4
first this is a test
second aaa bbb ccc ddd
Table 9-13. Sample Database Contents