Rice Lake 920i Installation Manual V1.05 - Manual (Page 78)

74 920i Installation Manual
SC.SMPRAT#n Sample rate 30, 60, 120, 240, 480, 960
SC.PWRUPMD#n Power up mode GO, DELAY
SC.TAREFN#n Tare function BOTH, NOTARE, PBTARE, KEYED
SC.PRI.DECPNT#n Primary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88, 888888.8,
8888888, 8888880, 8888800
SC.PRI.DSPDIV#n Primary units display divisions 1D, 2D, 5D
SC.PRI.UNITS#n Primary units LB, KG, G, OZ, TN, T, GN, TROYOZ, TROYLB, LT, CUSTOM, NONE
SC.SEC.DECPNT#n Secondary units decimal
position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88, 888888.8,
8888888, 8888880, 8888800
SC.SEC.DSPDIV#n Secondary units display divisions 1D, 2D, 5D
SC.SEC.UNITS#n Secondary units LB, KG, G, OZ, TN, T, GN, TROYOZ, TROYLB, LT, CUSTOM, NONE
SC.SEC.MULT#n Secondary units multiplier 0.00000–9999999
SC.TER.DECPNT#n Tertiary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88, 888888.8,
8888888, 8888880, 8888800
SC.TER.DSPDIV#n Tertiary units display divisions 1D, 2D, 5D
SC.TER.UNITS#n Tertiary units LB, KG, G, OZ, TN, T, GN, TROYOZ, TROYLB, LT, CUSTOM, NONE
SC.TER.MULT#n Tertiary units multiplier 0.000001–9999999
SC.ROC.DECPNT#n Tertiary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88, 888888.8,
8888888, 8888880, 8888800
SC.ROC.DSPDIV#n Rate-of-change units display
divisions 1D, 2D, 5D
SC.ROC.MULT#n Rate-of-change units multiplier 0.000001–9999999
SC.ROC.UNITS#n Rate-of-change units SEC, MIN, HOUR
SC.ROC.INTERVL#n Rate-of-change interval 1–65535
SC.ROC.REFRESH#n Rate-of-change refresh interval 1–65535
SC.ACCUM#n Accumulator enable ON, OFF
SC.VISIBLE#n Scale visibility ON, OFF
SC.WZERO#n Zero calibration —
SC.WVAL#n Test weight value test_weight_value
SC.WSPAN#n Span calibration —
SC.WLIN.F1#n–
SC.WLIN.F5#n Actual raw count value for
linearization points 1–5 0–16777215
SC.WLIN.V1#n–
SC.WLIN.V5#n Test weight value for linearization
points 1–5 0.000001–9999999
SC.WLIN.C1#n–
SC.WLIN.C5#n Calibrate linearization points 1–5 —
SC.LC.CD#n Set deadload coefficient —
SC.LC.CW#n Set span coefficient —
REZERO#n Rezero —
For commands ending with “#n”, n is the scale number.
Command Description Values
Table 9-3. SCALES Serial Commands (Continued)