Dell PowerEdge 2650 - Manual (Page 22)

E0212 VOLT CPU VRM Microprocessor VRM voltage is out of acceptable
range; faulty or improperly installed
microprocessor VRM; faulty system board. Ensure that supported VRMs of the same type are properly installed. If the
problem persists, replace the VRMs (see
Figure 6 -9 ). If the problem persists,
see " Getting Help ."
E0212 VOLT NIC 1.8V Integrated NIC voltage is out of acceptable
range; faulty or improperly installed power
supply; faulty system board. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0212 VOLT NIC 2.5V
E0212 VOLT PLANAR
REG
System board is out of acceptable voltage range;
faulty or improperly installed system board.
E0276 CPU VRM n Specified microprocessor VRM is faulty,
unsupported, improperly installed, or missing. Ensure that supported VRMs of the same type are properly installed. If the
problem persists, replace the VRM (see
Figure 6 -9 in "Installing System
Options"). E0276 MISMATCH VRM
n
E0280 MISSING VRM n
E0319 PCI OVER
CURRENT
Faulty or improperly installed expansion card. See " Troubleshooting Expansion Cards " in "Troubleshooting Your System."
E0412 RPM FAN n Specified cooling fan is faulty, improperly installed,
or missing. See " Troubleshooting a Cooling Fan " in "Troubleshooting Your System."
E0780 MISSING CPU 1 Microprocessor is not installed in socket 1. Install a microprocessor in socket 1 (see " Adding or Replacing a
Microprocessor " in "Installing System Options"). To identify microprocessor
socket 1, see Figure A -3 .
E07F0 CPU IERR Faulty or improperly installed microprocessor. See " Troubleshooting a Microprocessor " in "Troubleshooting Your System."
E07F1 TEMP CPU n
HOT
Specified microprocessor is out of acceptable
temperature range and has halted operation. See " Troubleshooting System Cooling " in "Troubleshooting Your System." If
the problem persists, ensure that the microprocessor heat sinks are properly
installed (see "
Adding or Replacing a Microprocessor " in "Installing System
Options").
E07F4 POST CACHE Faulty or improperly installed microprocessor. See " Troubleshooting a Microprocessor " in "Troubleshooting Your System."
E07F4 POST CPU REG
E07F4 POST CPU SMI SMI handler failed to initialize; faulty system
board. See " Getting Help ."
E07FA TEMP CPU n
THERM
Specified microprocessor is out of acceptable
temperature range and is operating at a reduced
speed, or frequency. See " Troubleshooting System Cooling " in "Troubleshooting Your System." If
the problem persists, ensure that the microprocessor heat sinks are properly
installed (see "
Adding or Replacing a Microprocessor " in "Installing System
Options").
E0876 POWER PS n No power available from the specified power
supply; specified power supply is improperly
installed or faulty. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0880 INSUFFICIENT
PS
Insufficient power is being supplied to the
system; power supplies are improperly installed,
faulty, or missing. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0CB2 MEM SPARE ROW Correctable errors threshold was met in a
memory bank: errors were remapped to the
spare row. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0CF1 MBE DIMM Bank
n
Memory modules installed in the specified bank
are not the same type and size; faulty memory
module(s). Ensure that all banks contain memory modules of the same type and size and
that they are properly installed. If the problem persists, see "
Troubleshooting
System Memory " in "Troubleshooting Your System."
E0CF1 POST MEM 64K Parity failure in the first 64 KB of main memory. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0CF1 POST NO
MEMORY
Main-memory refresh verification failure. Ensure that all banks contain memory modules of the same type and size and
that they are properly installed. If the problem persists, see "
Troubleshooting
System Memory " in "Troubleshooting Your System."
E0CF5 LOG DISABLE
SBE
Multiple single-bit errors on a single memory
module. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0D76 DRIVE FAIL Faulty or improperly installed hard drive or RAID
controller. See " Troubleshooting Hard Drives " and " Troubleshooting a RAID Controller
Card " in "Troubleshooting Your System."
E0F04 POST CMOS CMOS write/read failure; faulty system board. See " Getting Help ."
E0F04 POST CPU
SPEED
Microprocessor speed control sequence failure. See " Getting Help ."
E0F04 POST DMA INIT DMA initialization failure; DMA page register
write/read failure. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0F04 POST DMA REG Faulty system board. See " Getting Help ."
E0F04 POST KYB
CNTRL
Faulty keyboard controller; faulty system board. See " Getting Help ."
E0F04 POST MEM RFSH Main-memory refresh verification failure. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0F04 POST PIC REG Master or slave PIC register test failure. See " Getting Help ."
E0F04 POST SHADOW BIOS-shadowing failure. See " Troubleshooting System Memory " in "Troubleshooting Your System."
E0F04 POST SHD TEST Shutdown test failure.
E0F04 POST SIO Super I/O chip failure; faulty system board. See " Getting Help ."
E0F04 POST TIMER Programmable interval timer test failure; faulty
system board. See " Getting Help ."
E0F0B POST ROM
CHKSUM
Faulty or improperly installed expansion card. See " Troubleshooting Expansion Cards " in "Troubleshooting Your System."
E0F0C VID MATCH CPU
n
Specified microprocessor is faulty, unsupported,
improperly installed, or missing. See " Troubleshooting a Microprocessor " in "Troubleshooting Your System."
E10F3 LOG DISABLE BIOS disabled logging errors. Check the SEL for details on the errors.