E-flite Cessna 150 Aerobat 250 ARF - Manual (Page 4)

4 E-flite Cessna 150 Aerobat 250 ARF Assembly Manual
Contents of Kit/parts Layout
Replacement parts
EFL505001 Fuselage
EFL505002 Wing Panels left and right
EFL505003 Tail Set
EFL505004 Landing Gear Set
EFL505005 Cowling
EFL505006 Windshields
EFL505007 Hardware
EFL505008 Pushrods
EFL505009 Main Struts
EFL505010 Wing Tube
EFL505011 Wheel Pant Set
EFL505012 Decal Set
EFL505013 Wheel Set:
40mm (2), 35mm (1)
EFL505014 Main Hatch
Covering Colors
ParkLite, Orange HANU0814
ParkLite, True Red HANU0815
ParkLite, White HANU0801
hardware/Accessory Sizes
Main wheel 1.57-inch (40mm)
Nose wheel 1.37-inch (35mm)
Recommended Radio Equipment
You will need a minimum 4-channel transmitter,
receiver and four servos.
Recommended Transmitter
SPMR5510 DX5e DSMX ® 5-Channel
Transmitter Only
Additional Items
SPMAR6300 AR6300 DSM2 ™ Nanolite
6-Channel Receiver
EFLRDS35 DS35 Digital Super
Sub-Micro Servo (4)
SPMEXJST3UL 3-inch (76mm) Ultralight JST
Servo Extension (2) (rudder
and elevator extensions)
SPMEXJST6UL 6-inch (152mm) Ultralight JST
Servo Extension (4) (aileron
wing extension (2) and aileron
to fuselage extension (2))
SPMYHJST3UL 3-inch (76mm) Ultralight JST
Y-Harness (aileron to fuselage
extension Y-harness)
park 250 Motor Setup
EFLM1130 Park 250 Brushless Outrunner
Motor, 2200Kv
EFLA1010 10-Amp Pro Brushless ESC
EFLB4302SJ 430mAh 2S 7.4V 20C Li-Po,
20AWG
GWSEP7035B 7 x 3.5 Direct Drive Propeller
park 280 Motor Setup
EFLM1140 Park 280 Brushless Outrunner
Motor, 1800Kv
EFLA1010 10-Amp Pro Switch-Mode BEC
Brushless ESC
EFLB4503SJ30 450mAh 3S 11.1V 30C LiPo,
18AWG JST
GWSEP7035B 7 x 3.5 Direct Drive Propeller
Optional Accessories
EFLSP100 1.00-inch Aluminum Spinner
with 2mm Collet
EFLA110 Power Meter
EFLC3025 Celectra ™ 80W AC/DC Multi-
Chemistry Battery Charger
Required Tools and Adhesives
Tools & Equipment
Dental floss Paper towels
Felt-tipped pen Flat blade screwdriver: 1.5mm
Flat file Hemostat
Hex wrench: 1.5mm Hobby knife with #11 blade
Low-tack tape Open-end wrench: 6mm
Pencil Phillips screwdriver: #0, #1, #2
Pin vise Razor saw
Ruler Scissors
Square Toothpicks
Rubbing alcohol Side cutters
Drill bit: #56/.046 (1mm), 1/16-inch (1.5mm),
5/64-inch (2mm)
Optional Tools & Equipment
Balancing stand (optional)
Adhesives
Medium CA PAAPT02
Thin CA PAAPT08
Threadlock PAAPT42
Canopy Glue PAAPT56