Brandmotion 9002-9504-V1 - Manual (Page 2)

Installation Instruction Overview - Rear Vision System Mirror Display
2007-2013 Chevy Silverado and GMC Sierra
(Kit Part numbers 9002-9503 without Compass/Temp and 9002-9504 with Compass/Temp
9503 & 9504 Instruction Overview 7-11-13.doc Page 2 of 2
Plug Supplied Mirror Harness into Mirror Connector (Steps 52 thru 59 in supplied complete kit instructions)
52 Use a digital multimeter or computer safe test light to test cavity 9 for Reverse signal.
A. If Reverse signal is present in cavity 9, proceed to Step 53.
B. If Reverse signal is NOT present in cavity 9, check for wires in cavities 13 and 8. If cavities 13 and 8 do NOT contain wires,
proceed to Step 57.
C. If Reverse signal is NOT present in cavity 9 and cavities 13 and 8 contain wires, remove and isolate any pin present in cavity 9.
Figure 29. Then, plug the 16-pin terminal of the supplied Green 6’ Wire into cavity 9. Next, splice the opposite end of supplied Green 6’ Wire
into the Green wire on the supplied Mirror Harness using solder and cover with heat shrink tubing (recommended) or using T-taps as an
alternate method. Proceed to Step 53.
53 Unlock white TPA (Terminal Position Assurance) tab from vehicle’s mirror connector.
54-56 Insert Gray/Dark Blue and Gray/Orange wires from supplied foam-wrapped mirror harness into vehicle’s mirror connector
according to chart on Page 1. NOTE: If wires exist in either of these cavities, remove and isolate.
57 If your vehicle is NOT equipped with an auto dimming mirror and wires are NOT present in cavities 9, 13, or 8,
you must purchase a 9002-6105 harness separately from Brandmotion and connect it as follows:
a. Insert Brown reverse terminal (if 6105 harness has gray jacket) or Green reverse wire (if 6105 harness has black jacket) from 6105 harness
into cavity 9.
b. Insert Green ignition terminal (if 6105 harness has gray jacket) or Red ignition wire (if 6105 harness has black jacket) from 6105 harness into
cavity 13.
c. Insert White ground terminal (if 6105 harness has gray jacket) or Black ground wire (if 6105 harness has black jacket) from 6105 harness into
cavity 8.
d. Splice Brown reverse wire (if 6105 harness has gray jacket) or Green reverse wire (if 6105 harness has black jacket) at the RCA connector
end of 6105 harness to the Green reverse wire of the supplied foam wrapped Mirror Harness.
e. Splice Green ignition wire (if 6105 harness has gray jacket) or Red ignition wire (if 6105 harness has black jacket) at the RCA connector end
of 6105 harness to the Pink ignition wire of the supplied foam wrapped Mirror Harness.
f. Splice White ground wire (if 6105 harness has gray jacket) or Black ground wire (if 6105 harness has black jacket) at the RCA connector end
of 6105 harness to the Black ground wire of the supplied foam wrapped Mirror Harness.
58-59 Press down on TPA device to lock wires into the vehicle’s mirror connector, and route other end of the supplied mirror harness
down the driver’s side instrument panel near the A-pillar.
Connect Supplied Mirror Harness to Power, Reverse, and Ground (Steps 60 thru 69 in supplied complete kit
instructions)
NOTE: Follow Steps 60-67 only if you located reverse signal at the C10/X10 or C11/X11 M-BEC Connector (Steps 30-33) . If
reverse was not present, proceed to Step 68.
60-61 Remove brown C12/ X12 connector from M-BEC and remove the TPA from C12/ X12
62
Insert the Pink wire (ignition) from the supplied mirror harness into cavity 7, reinsert the TPA into Connector C12/ X12, and
reinstall C12/ X12 connector into M-BEC. NOTE: Pickups with cooled seats require a Denali Jumper Harness, Brandmotion kit
# 9002-6005, available separately.
63-65 Remove light gray C11/ X11 or gray C10/ X10 connector from M-BEC and remove TPA from C11/ X11 or C10/ X10 connector.
66
If cavity 5 is not populated, connect Jumper Harness to the black mirror harness connector, and insert Green wire of the
Jumper Harness into cavity 5 of C11/ X11 Connector OR cavity 8 of C10/ X10 connector. Proceed to Step 68.
66 If cavity 5 is populated, remove the Blue wire from C11 connector cavity 5. Unlock the gray TPA on the black connector on the
mirror harness. Insert Blue terminal into open cavity of the Jumper Harness. Slide gray TPA to lock the wires. Snap Jumper
Harness onto the black mirror connector. Then, insert green Jumper Harness wire into C11/ X11 connector cavity 5.
67 Reinsert the TPA, and reinstall C11/ X11 connector back into the M-BEC. Proceed to Step 68.
68 If all M-BEC connections were secure and no fuses were blown and reverse was still not present, reverse must be
located in the under dash BCM left of the steering wheel.
A. Cut connector off Green Reverse (+) wire of Mirror Harness and splice to wire in Brown BCM X5 Connector Cavity 11.
B. Cut terminal off Pink ignition (+) wire of supplied Mirror Harness and splice to wire in Brown BCM X5 Connector Cavity 13.
69 Attach Ground eyelet on black wire of supplied Mirror Harness to lower knee bolster support bolt with supplied Ground Nut.
Install Supplied Rear View Mirror (Steps 70 thru 80 in supplied complete kit instructions)
70-72 Insert vehicle’s mirror connector into the supplied Mirror, slide the Mirror on the windshield mounting tab, and torque the
screw to 1.8 Nm (16 lb-in)—do not exceed 2.2 Nm (19.5 lb-in).
73-80 Lower the front of the headliner and route supplied mirror harness toward A-pillar. Reinstall mirror wire cover, overhead
console assembly and driver’s side sunshade.
Install Chassis Harness (Steps 81 thru 98 in supplied complete kit instructions)
81-87 Locate longer Chassis Harness from kit. Route the grommet end of Chassis Harness through drilled hole in the front of dash,
seat the grommet, and connect to the supplied mirror harness. Reinstall MBEC and MBEC cover.
88-89 Route the Chassis Harness towards the rear of the vehicle and along the vehicle’s chassis harness.
90
Connect the supplied Chassis Harness to the supplied camera harness.
91 Secure supplied harnesses to existing harness using supplied Wire Ties every 200mm (approx. 8”).
92-98 Reinstall negative battery cable and test system. Secure the mirror harness to existing wiring in the A-pillar and dash using
supplied Wire Ties. Reinstall remaining previously removed interior parts.