Index – Rockwell Automation GV3000 AC Pwr Module Ver. 5.0 Hardware Ref, Installation, and Troubleshooting User Manual
Page 87

IndexĆ1
Index
A
AĆC input
diodes, checking, 9Ć6 to 9Ć7
disconnect, installing, 5Ć2 to 5Ć4
isolation transformer, 5Ć1
line branch circuit fuses, 3Ć7 to 3Ć8, 5Ć1 to 5Ć3
ratings, 2Ć2
wire sizes, 3Ć5 to 3Ć6
wiring, 3Ć5 to 3Ć7, 4Ć1 to 4Ć8, 5Ć1 to 5Ć5
voltage transients, avoiding, 5Ć1
AĆC output
wiring, 3Ć5 to 3Ć7, 4Ć1 to 4Ć8, 6Ć1 to 6Ć2
Air flow, 3Ć1, 3Ć4
Alarms, 9Ć1
Altitude requirements, 3Ć1
Ambient conditions, 3Ć1, AĆ1
Analog output, 2Ć9
0Ć10 VDC (J17), 2Ć9 to 2Ć11, 2Ć13, AĆ2
4Ć20 mA (J17), 2Ć9 to 2Ć11, 2Ć13, AĆ2
wiring, 2Ć14, 7Ć1, 7Ć3 to 7Ć4, 7Ć8
Analog input speed reference
input current, wiring, 2Ć14, 7Ć1, 7Ć3 to 7Ć4, 7Ć9,
ąAĆ2
input voltage, wiring, 2Ć14, 7Ć1, 7Ć3 to 7Ć4, 7Ć9,
ąAĆ2
0Ć10 VDC (J4), 2Ć10 to 2Ć12, 7Ć1
4Ć20 mA (J4), 2Ć10 to 2Ć12, 7Ć1
Area required, 3Ć2 to 3Ć4
Audience, intended, 1Ć2
B
Block diagram
vector regulation, BĆ3
volts/hertz regulation, BĆ2
Board
Bus Clamp, 2Ć7 to 2Ć8, 9Ć11 to 9Ć12
Capacitor, 2Ć3 to 2Ć5, 9Ć8 to 9Ć9
Current Feedback, 2Ć3 to 2Ć5, 9Ć8
Gate Driver, 2Ć5 to 2Ć8, 9Ć9 to 9Ć12
Intelligent Power Module (IPM), 2Ć7 to 2Ć8, 9Ć11
to 9Ć12
Option, 2Ć15, 2Ć16
Power, 2Ć5, 2Ć6, 9Ć9, 9Ć10
Power Supply, 2Ć5, 2Ć6, 9Ć9, 9Ć12
Regulator, 2Ć3 to 2Ć14, 3Ć7, 9Ć8 to 9Ć10
Thyristor Precharge, 2Ć8, 9Ć12
Braking, snubber resistor, 2Ć9, 2Ć16, 5Ć1, AĆ2
wiring, 2Ć14, 7Ć2 to 7Ć4, 7Ć14
Bus clamp board, 2Ć7 to 2Ć8, 9Ć11 to 9Ć12
C
Capacitor board, 2Ć3 to 2Ć5, 9Ć8 to 9Ć9
Capacitors, DĆC bus, 9Ć1 to 9Ć5
Carrier frequency, 2Ć9, AĆ1
CS3000, see Control and Configuration Software
Closed loop, see Vector Regulation
Communication port (J8), 2Ć10 to 2Ć11, 2Ć15, 3Ć7,
7Ć1, 7Ć7
Communication, network, 2Ć15, 3Ć7
Component locations, 2Ć3 to 2Ć8
Conduit size, 4Ć2 to 4Ć7
Control and Configuration Software, 1Ć2, 2Ć16, 3Ć7,
7Ć7
Contacting Reliance, 1Ć2
Contactors, installing output, 6Ć1
Contacts
Form A, 2Ć9, 7Ć15
Form B, 2Ć9, 7Ć15
Control source, 7Ć1, 7Ć3 to 7Ć4, 7Ć7
PC, 3Ć7, 7Ć1, 7Ć7
wiring, 7Ć3 to 7Ć4, 7Ć7
Control, wiring, 2Ć13, 7Ć1 to 7Ć15
Current Feedback board, 2Ć3 to 2Ć5, 9Ć8
Current transformer, 2Ć7 to 2Ć8, 9Ć11 to 9Ć12
D
DĆC bus
input wiring, 3Ć5 to 3Ć6, 4Ć1 to 4Ć8, 5Ć3, 5Ć5
fuse, 2Ć7 to 2Ć8, 9Ć11 to 9Ć12
terminals, 9Ć1 to 9Ć5
verifying capacitor voltage, 9Ć1 to 9Ć5
Digital input wiring, 2Ć14, 7Ć2 to 7Ć4, 7Ć10 to 7Ć14
8 (remote/local), 7Ć2 to 7Ć4, 7Ć10
7 (ramp1/ramp2), 7Ć2 to 7Ć4, 7Ć11
6 (forward/reverse), 7Ć2 to 7Ć4, 7Ć12
5 (function loss), 7Ć2 to 7Ć4, 7Ć13
4 (run/jog), 7Ć2 to 7Ć4, 7Ć13
3 (reset), 7Ć2 to 7Ć4, 7Ć14
2 (stop), 7Ć2 to 7Ć4, 7Ć14
1 (start), 7Ć2 to 7Ć4, 7Ć14
Digital output wiring, see Status Relays
Dimensions, 3Ć2 to 3Ć3
Disconnect, installing AĆC input, 5Ć2 to 5Ć4
Display, see Keypad/Display
Distribution system capacity, AĆC line maximum, 5Ć1
Drive,
identifying, 2Ć1
kits, 2Ć16