Routine maintenance overview checklist – MTS Criterion Series 40 User Manual
Page 126
Routine Maintenance Overview Checklist
Recommended Service
Annually
Weekly
Daily
Calendar Time Using 8 Hours Running Time Rate
per Day
2000
40
8
Running Time-Hours
PC Maintenance
MTS
1
Back up testing software files (*.reg/.cal files).
MTS
Defragment hard drive.
System Inspection
MTS
2
Back up testing software files (*.reg/.cal files).
MTS
Check/adjust drive belt tension (refer to table).
MTS
Inspect drive belts for excessive wear.
MTS
X
Inspect cable connections.
System Checks
MTS
X
Check Emergency-Stop.
X
Activate and reset limits.
MTS
Check upper limit.
MTS
Check lower limit.
MTS
X
Check load cal/shunt calibration.
Lubrication
1
Denotes service performed by trained field service engineers as part of an MTS Routine Maintenance plan.
Some of these procedures require special service tools and/or specific service training to complete.
2
Denotes service performed by trained field service engineers as part of an MTS Routine Maintenance plan.
Some of these procedures require special service tools and/or specific service training to complete.
126 | MTS Criterion
™
Series 40
Maintenance
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)