INFICON VGC403 Three-Channel Measurement and Control Unit User Manual
Vgc402, Vgc403, Operating manual
This manual is related to the following products:
Table of contents
Document Outline
- VGC402
- VGC403
- 1 Introduction
- 2 Technical data
- 3 Installation
- 4 Operation
- 5 Parameter
- 5.1 Switching function parameters (PArA SP)
- 5.2 Sensor parameters (PArA SEn)
- 5.2.1 Measurement filter (FiLt)
- 5.2.2 Gas type (GAS)
- 5.2.3 Measuring range (FS)
- 5.2.4 Offset (oFS)
- 5.2.5 Degas function (dEGAS)
- 5.2.6 Sensor activation (S-on)
- 5.2.7 Switch-on threshold (t-on)
- 5.2.8 Sensor deactivation (S-oFF)
- 5.2.9 Switch-off threshold (t-off)
- 5.2.10 Emission (EMi)
- 5.2.11 Filament selection (FiL)
- 5.2.12 Pirani range extension (PrE)
- 5.3 General parameters (PArA GEn)
- 5.4 Test parameters (PArA tESt)
- 5.4.1 Selection
- 5.4.2 Firmware version (Pnr)
- 5.4.3 Watchdog control (dt-C)
- 5.4.4 Torr lock (tr-L)
- 5.4.5 Parameter setup lock (LoC)
- 5.4.6 RAM test (rA-t)
- 5.4.7 EPROM test (EP-t)
- 5.4.8 EEPROM test (EE-t)
- 5.4.9 Display test (di-t)
- 5.4.10 A/D converter signal (Ad-S)
- 5.4.11 A/D converter ID (Ad-i)
- 5.4.12 I/O test (io-t)
- 5.4.13 RS232C test (rS-t)
- 6 Computer interface
- 6.1 Basics
- 6.2 Communication
- 6.3 Mnemonics
- 6.3.1 Overview
- 6.3.2 AOM
- 6.3.3 BAU
- 6.3.4 COM
- 6.3.5 COR
- 6.3.6 DCD
- 6.3.7 DGS
- 6.3.8 ERA
- 6.3.9 ERR
- 6.3.10 EUM
- 6.3.11 FIL
- 6.3.12 FSR
- 6.3.13 FUM
- 6.3.14 GAS
- 6.3.15 HVC
- 6.3.16 ITR
- 6.3.17 LOC
- 6.3.18 OFC
- 6.3.19 OFD
- 6.3.20 PNR
- 6.3.21 PR1
- 6.3.22 PRE
- 6.3.23 PRX
- 6.3.24 RES
- 6.3.25 SAV
- 6.3.26 SC1
- 6.3.27 SP1
- 6.3.28 SPS
- 6.3.29 TAD
- 6.3.30 TDI
- 6.3.31 TEE
- 6.3.32 TEP
- 6.3.33 TID
- 6.3.34 TIO
- 6.3.35 TKB
- 6.3.36 TLC
- 6.3.37 TRA
- 6.3.38 TRS
- 6.3.39 UNI
- 6.3.40 WDT
- 7 Maintenance and service
- 8 Troubleshooting
- 9 Storage and disposal
- Appendix