INFICON HLD6000 Refrigerant Leak Detector Interface Description User Manual
Page 9
ASCII Protocol
9
*CONFig:STANDBYDel
Auto standby time in minutes 1…15, 0=OFF
480
R/W
*CONFig:TRIGger1
desired trigger1 in selected unit
R/W
*CONFig:TRIGger1:G/a desired trigger1 in g/a
385
R/W
*CONFig:TRIGger1:LB/yr
desired trigger1 in lb/yr
R/W
*CONFig:TRIGger1:MBAR*l/s desired trigger1 in mbar*l/s
R/W
*CONFig:TRIGger1:OZ/yr
desired trigger1 in oz/yr
R/W
*CONFig:TRIGger1:PA*m3/s
desired trigger1 in Pa*m3/s
R/W
*CONFig:TRIGger2
desired trigger2 in selected unit
R/W
*CONFig:TRIGger2:G/a desired trigger2 in g/a
385
R/W
*CONFig:TRIGger2:LB/yr
desired trigger2 in lb/yr
R/W
*CONFig:TRIGger2:MBAR*l/s desired trigger2 in mbar*l/s
R/W
*CONFig:TRIGger2:OZ/yr
desired trigger2 in oz/yr
R/W
*CONFig:TRIGger2:PA*m3/s
desired trigger2 in Pa*m3/s
R/W
*CONFig:UNIT
leak rate unit (g/a, lb/yr, mbar*l/s, oz/yr, Pa*m3/s)
432
R/W
*CONFig:UNIT:LR
leak rate unit (g/a, lb/yr, mbar*l/s, oz/yr, Pa*m3/s)
432
R/W
*CONFig:USERGASFAC1
Factor for user gas 1
485
R/W
*CONFig:USERGASFAC2
Factor for user gas 2
485
R/W
*CONFig:USERGASFAC3
Factor for user gas 3
485
R/W
*CONFig:VOLume
Volume (1…15)
420
R/W
*FACtor:CAL
Calibration factor
460
R/W
*FACtor:CALOFFset
Leak rate offset in g/a when sniffing air. Only valid for CO2
sniffer probes.
488
R/W
*FACtor:PHASE
Phase
459
R/W
*HOUR:DATE
Date (DD,MM,YYYY)
450
R/W
*HOUR:DEVice
operating hours of device
142
R
*HOUR:POWer
time since switching on (in minutes)
147
R
*HOUR:SNiffer
operating hours of sniffer probe
152
R
*HOUR:TIME
Time (HH,MM)
450
R/W
*IDN:BOOTversion
software version bootloader main board
318
R
*IDN:CRC
check sum
320
R
*IDN:CUversion
software version control unit
314
R
*IDN:DEVice
name of instrument (HLD6000)
301
R
*IDN:IOBOOTversion
software version boot loader I/O module
319
R
*IDN:IOSERIAL
Serial number I/O module
408
R
*IDN:IOversion
software version I/O module
313
R
*IDN:IRSENSERIAL
Serial number of IR-sensor
407
R
*IDN:PROBE
Probe HEX code
458
R
*IDN:PROBEBOOTversion
software version boot loader sniffer probe
332
R
*IDN:SERial
serial-number leak detector
406
R
*IDN:SNSerial
Serial number of sniffer probe
404
R
*IDN:SNVersion
Software version of sniffer probe
312
R
*IDN:TESTLeak
Test leak info
457
R
*IDN:VERsion
software version main board
310
R
*MEASure:ACCEL
Probe acceleration value
178
R
*MEASure:ACTTRIGger1
Actual trigger in selected unit
R
Command
Meaning
Relates
to LD
cmd. no.
Read /
Write