Conversions – INCRA Miter 5000 with Sled & Telescoping Fence User Manual
Page 8
Place a
9
⁄
16
" o.d. nylon washer on the
1
⁄
4
-20 x
3
⁄
4
"
thumbscrew. Carefully position the remaining (2)
9
⁄
16
" nylon
and (1)
9
⁄
16
" steel washers in a stack directly over the
1
⁄
4
-20
hole on the Miter5000 mounting plate. Now pivot the slotted hole
on the rear actuator over the washer stack and insert the
1
⁄
4
-20 x
3
⁄
4
" thumbscrew through the slotted hole and washers. Thread the
thumbscrew
into the
mounting
plate.
Place the
remaining
1
⁄
2
" o.d.
steel washer
in the
recessed
hole on the
Miter5000
sled base
as shown,
Fig.-33
Place the
1
⁄
2
" o.d. x
3
⁄
32
" thick nylon washer on the supplied
1
⁄
4
x
1
⁄
2
" shoulder bolt, then insert through the pivot hole
on the rear actuator. Now add (2)
9
⁄
16
" o.d. nylon washers
followed by
(1)
1
⁄
2
" o.d.
steel washer
and thread
the shoulder
bolt into
the #10-24
hole on the
Miter5000
mounting
plate,
Fig.-32.
Tighten the
shoulder bolt.
Using the supplied
1
⁄
4
x
3
⁄
4
" shoulder bolt and the
1
⁄
2
" o.d. x
5
⁄
32
" thick nylon washer, attach the protractor top and bottom
plates to the Miter5000 sled base. Tighten the shoulder bolt.
Place (1) large steel washer on the large clamping knob and screw
through the slotted holes in the protractor top and bottom plates into
the Miter5000 sled base,
Fig.-35.
9
⁄
16
" o.d.
nylon
washers
Place
1
⁄
2
" o.d.
steel washer
in recess
9
⁄
16
" o.d. steel washer
Stack
these
washers
then slide
between
mounting
plate and
actuator
Carefully remove the
1
⁄
4
-20 x
3
⁄
4
" thumbscrew,
1
⁄
4
x
1
⁄
4
"
shoulder bolt and all washers from the rear actuator,
Fig. 31.
Combined with the washers in the conversion hardware pack,
you will need the following washers to attach the rear actuator to the
mounting plate on the Miter5000 sled base:
(5)
9
⁄
16
"
o.d. nylon
washers
(1)
9
⁄
16
" o.d.
steel washer
(2)
1
⁄
2
" o.d.
steel washers
(1)
1
⁄
2
" o.d.
x
3
⁄
32
" thick
nylon washer
Remove the fence from the protractor head. Remove the
large clamping knob,
1
⁄
4
x
5
⁄
8
" shoulder bolt and washers that
secure the protractor to the miter bar. Lift the protractor top
and bottom plates off,
Fig. 34.
Made in America by: Taylor Design Group, Inc. • P.O. Box 810262, Dallas, Texas 75381, 972-242-9975, www.incra.com
02-2001
FIG. 31
FIG. 33
FIG. 34
1
2
3
4
FIG. 32
Important:
If you have purchased the Miter3000 to Miter5000 Conversion
Kit, it includes a large clamping knob with a
15
⁄
16
" thread
length. Use this longer thread length in attaching the
protractor head to the Miter5000 sled base.
Continue with the "Assembly" and “Calibration” instructions
beginning on page 3.
5
FIG. 35
Converting Miter3000 Miter Gauge to Miter5000 Miter sled
note: When a shoulder bolt is called out in the instructions, (for example:
1
⁄
4
x
1
⁄
2
" shoulder bolt), the first dimension
refers to the diameter of the shoulder, while the second dimension describes the length of the shoulder, not the threads.
Conversions
Additional
9
⁄
16
" o.d. washers
from conversion hardware pack
1
⁄
2
" o.d.
steel washer
9
⁄
16
" o.d.
nylon washers
1
⁄
2
" o.d. x
3
⁄
32
"
thick nylon
washer
1
⁄
4
x
1
⁄
2
"
shoulder bolt
Large clamping knob
with
15
⁄
16
" thread length
Large steel washer
1
⁄
2
" o.d. x
5
⁄
32"
nylon washer
1
⁄
4
x
3
⁄
4"
shoulder
bolt
8