Barco R9002328 - Manual (Page 134)

R5975059A BARCOVISION 708 200498
OPTIONS
OPTIONS
R5975059A BARCOVISION 708 200498
OPTIONS
OPTIONS
11-3 11-3
Projector Control software
Only available for projectors equipped with the optional RS232 communication
port.
The software is user-friendly and makes full use of : mouse control, pull down
menus and dialogue boxes.
Two main applications are available with this software : remote control and
transferring and receiving data of projector settings.
remote control simulation. Advantage : address range 0 to 15.
adjustment data : where can it be located when an IBM PC (or compatible) or MAC
or Workstation is connected :
- hard memory device with files of settings.
- the contents of the local memory of the computer.
- the contents of the projector.
RCVDS 05
An optional RCVDS 05 source selector makes it possible to connect up to 20
sources to the projector. When RCVDS's are linked via the expansion module,
even 90 inputs can be connected to the projector.
The selected source number will be displayed on a 2 digit display and the selected
input module will be indicated with a LED on the rear.
VS05
The VS05 is a versatile Video and HDTV source selector for all BARCO's digitally
controlled large screen projectors. It offers the possibility to connect and switch
up to 5 different Video sources, 3 different S-Video sources and 1 RGB Analog
source to a BARCO projector. In addition, the audio signal proper to the source,
can be switched to an audio amplifier.
Adapter and communication cables
BARCO provides several cables to connect peripheral equipment to the projector.
a. D9-D9 communication cable
- To connect an IBM PC (or compatible) to the projector. (only if the optional
RS232 port is installed.)
- To connect an RCVDS to the projector.
- To connect an IR receiver to the RCVDS05 or to the projector.
- To be used as extension cable for all other adapter cables.
Available length :5 m (16ft), order number R982770; 15 m(50ft), order number
R9827560; and 30 m (100ft), order number R9827570
Projector Control software
Only available for projectors equipped with the optional RS232 communication
port.
The software is user-friendly and makes full use of : mouse control, pull down
menus and dialogue boxes.
Two main applications are available with this software : remote control and
transferring and receiving data of projector settings.
remote control simulation. Advantage : address range 0 to 15.
adjustment data : where can it be located when an IBM PC (or compatible) or MAC
or Workstation is connected :
- hard memory device with files of settings.
- the contents of the local memory of the computer.
- the contents of the projector.
RCVDS 05
An optional RCVDS 05 source selector makes it possible to connect up to 20
sources to the projector. When RCVDS's are linked via the expansion module,
even 90 inputs can be connected to the projector.
The selected source number will be displayed on a 2 digit display and the selected
input module will be indicated with a LED on the rear.
VS05
The VS05 is a versatile Video and HDTV source selector for all BARCO's digitally
controlled large screen projectors. It offers the possibility to connect and switch
up to 5 different Video sources, 3 different S-Video sources and 1 RGB Analog
source to a BARCO projector. In addition, the audio signal proper to the source,
can be switched to an audio amplifier.
Adapter and communication cables
BARCO provides several cables to connect peripheral equipment to the projector.
a. D9-D9 communication cable
- To connect an IBM PC (or compatible) to the projector. (only if the optional
RS232 port is installed.)
- To connect an RCVDS to the projector.
- To connect an IR receiver to the RCVDS05 or to the projector.
- To be used as extension cable for all other adapter cables.
Available length :5 m (16ft), order number R982770; 15 m(50ft), order number
R9827560; and 30 m (100ft), order number R9827570