EUCHNER CES-AZ-UES-xxx (Multicode) - Manual (Page 23)

Operating Instructions Safety System CES-AZ-UES-...
23
Technical Data CES-AZ-AES-01B
Parameter
Value
Unit
min. typ. max.
Housing material Plastic PA6.6
Dimensions 114 x 99 x 22.5 mm
Weight 0.2 kg
Ambient temperature at U
B
= DC 24 V -20 - +55 °C
Atmospheric humidity, not condensing - - 80 %
Degree of protection IP20
Degree of contamination 2
Installation DIN rail 35 mm according to EN 60715
Number of read heads 1 read head per evaluation unit
Connection (plug-in screw terminals/coded) 0.14 - 2.5 mm²
Operating voltage U
B
(regulated, residual ripple < 5 %) 21 24 27 V DC
For the approval according to the following applies Operation only with UL Class 2 power supply, or equivalent measures
Current consumption I
B
(with relay energized) 1) - 150 - mA
External fuse (operating voltage U
B
) 0.25 - 8 A
Safety contacts 2 (relays with internally monitored contacts)
Switching current (relay outputs)
mA
- At switching voltage AC/DC 21 ... 60 V 1 - 300
- At switching voltage AC/DC 5 ... 30 V 10 - 4000
- At switching voltage AC 5 ... 230 V (160 V ATEX) 10 - 2000
Switching load according to Max. AC 30 V, class 2 / max. DC 60 V, class 2
External fuse (safety circuit) according to EN 60269-1 6 A gG or 6 A circuit breaker (characteristic B or C)
Utilization category to EN 60947-5-1 AC-12 60V 0.3A / DC-12 60V 0.3A
AC-12 30V 4A / DC-12 30V 4A
AC-15 230V 2A / DC-13 24V 3A
Classification according to EN 60947-5-3 PDF-M
Rated insulation voltage U
i
250 V
Rated impulse withstand voltage U
imp
4 kV
Rated conditional short-circuit current 100 A
Resilience to vibration In acc. with EN 60947-5-2
Mechanical operating cycles (relays) 10 x 10 6
Switching delay from state change 2) - - 210 ms
Time difference (between the switching points of the two
relays)
- - 25 ms
Current via feedback loop Y1/Y2 5 8 10 mA
Permissible resistance via feedback loop - - 600 Ω
Ready delay 3) - 10 12 s
Dwell time 4) 3 - - s
Switching frequency max. 5) - - 0.25 Hz
Repeat accuracy R according to EN IEC 60947-5-3 ≤ 10 %
Monitoring outputs (diagnostics DIA, door monitoring output
O1, semiconductor output, p-switching, short-circuit pro-
tected)
- Output voltage 0.8 x U
B
- U
B
V DC
- Max. load - - 20 mA
Start button input S, test input TST
- Input voltage LOW 0 - 2
V DC
HIGH 15 - U
B
- Input current HIGH 5 8 10 mA
EMC protection requirements In acc. with EN 60947-5-3
Reliability figures according to EN ISO 13849-1
as a function of the switching current at 24 V DC ≤ 0.1 A ≤ 1 A ≤ 3 A
Category 4
Performance Level (PL) e
PFH
d
1.9 x 10 -8
Mission time 20 years
Number of switching cycles/year 760 000 153 000 34 600
1) Without taking into account the load currents on the monitoring outputs.
2) Corresponds to the risk time according to EN 60947-5-3. This is the maximum switch-off delay for the safety outputs following removal of the actuator. In case of EMC interference in excess
of the requirements in accordance with EN 60947-5-3, the switch-off delay can increase to max. 250 ms. After a brief actuation < 0.25 s, the switch-on delay can increase to max. 3 s if this is
followed immediately by further actuation.
3) After the operating voltage is switched on, the relay outputs are switched off and the door monitoring contact is set LOW during the ready delay. For the visual indication of the delay, the green
STATE LED flashes at a frequency of approx. 15 Hz.
4) The dwell time is the time that the actuator must be inside or outside the operating distance.
5) In case of monitoring with feedback loop, the actuators must remain outside the operating distance, e.g. with a door open, until the feedback circuit is closed.