Operating manual – BAND-IT BT1000 Boss Tool User Manual
Page 8
BT1000
BOSS
TM
Tool
www.band-it-idex.com
Document # P98750 Rev. B
©
Copyright
BAND-IT-IDEX, Inc. 2013
All rights reserved
Page 8
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
Operating Manual
BT1000 BOSS
TM
Tool Manual
Operation
5. Releasing the tool
The tool can now be released from the strapping without any
further action after completing the strapping cycle. By lifting
the air motor, the band end is removed from the tool.
6. Tension adjustment
The tension can be adjusted by adjusting the throttle screw. The air
supply is reduced by turning the screw clockwise, hence reducing
the tension.
The throttle screw is located at the rear end of the air motor.
Note: The tool tension speed has been factory set to maximum.
- A92079 Tie-Lok II (4 pages)
- A94079 Ultra-Lok (4 pages)
- A95079 Band-Lok (3 pages)
- Ball-Lok Ties Installation (1 page)
- Ties Installation (1 page)
- Ball-Lok Installation (1 page)
- C00169 banding (2 pages)
- C00169 Hand Tool (4 pages)
- C00269 JR. Hand Tool (3 pages)
- C00369 Heavy Duty Tool (4 pages)
- C06599 Tension Limiter (2 pages)
- C07569 Bantam Hand Tool (3 pages)
- C08569 Bantam Strapping Hand Tool (4 pages)
- C40099 Ratchet Banding Tool (1 page)
- CB1000 Hand Tool (4 pages)
- D50089/99 Bolted Band Retainer (1 page)
- D51089 (1 page)
- G40269 Giant II Hand Tool (3 pages)
- Gripper Installation (1 page)
- ID200 Series Imprinter (14 pages)
- ID3016 ID Tag Imprinter (1 page)
- ID4002 SS Tape Embosser (2 pages)
- IT0750-AB Mini Tie-Lok Tool (38 pages)
- IT1000-AB 1/4 Tie-Lok Tool (38 pages)
- IT2000-AB 1/4 Junior Tool (38 pages)
- IT3000-AB 1/4 Ultra-Lok Tool (28 pages)
- IT4000-AB 5/16 Band-Lok Tool (28 pages)
- IT5000-AB 3/8 Junior Tool (38 pages)
- IT6000-AB 3/8 Tie-Lok Tool (38 pages)
- J00169 JR. Tool Adapter (2 pages)
- J02069 Pok-It II Tool (2 pages)
- J05069 Heavy Duty Adapter (2 pages)
- J07589/99 Thriftool (2 pages)
- J93099 Cutter Blade Kit (2 pages)
- K50289 Ball-Lok/Self-Lok Tool (5 pages)
- M15650 Scru-Band Kit (1 page)
- M21050 Scru-Seal (1 page)
- M50389 Multi Lok Tool (5 pages)
- Q Band Installation (1 page)
- S03869 Center Punch Tool (2 pages)
- S100 Classic Air Tool (18 pages)
- S35099 Automatic Air Tool (34 pages)
- S75099 Pneumatic Junior Clamp Application Tool (21 pages)
- Shield-Lok SL4099 Tool Pack (15 pages)