NOVUS N120/N125 CONTROLLER - Manual (Page 2)

2
0023 Serial
number H
Serial Number High (Upper display).
Range: 0 to 9999. Read only.
0024 Serial
number L
Serial Number Low (Lower display).
Range: 0 to 9999. Read only.
0025 SV Control Setpoint (Prompt Setpoint).
Range: from spll to spkl.
0026 spll Setpoint Low limit.
Range: minimum value depends on the input type selected
in type (see Table 1) to spkl.
0027 spkl Setpoint High limit.
Range: minimum value is spll and maximum depends on
the input type selected in type (see Table 1).
0028 Reserved Internal use.
0029 offs Offset value of PV(Process value).
Range: from spll to spkl.
0030 dppo PV decimal point position
Range: 0 to 3
0  0.000; 1  00.00; 2  000.0; 3  0000
0031 Sp.a1 Alarm 1 Setpoint.
Range: From spll to spkl for non differential; and
spkl - spll for differential alarm.
0032 Sp.a2 Alarm 2 Setpoint. Range: same as in spa1.
0033 Sp.a3 Alarm 3 Setpoint. Range: same as in spa1.
0034 Sp.a4 Alarm 4 Setpoint. Range: same as in spa1.
0035 Fva1 Alarm 1 Function. Range: 0 to 8
0  off
1  ierr
2  T.END
3  rs
4  lo
5  ki
6  dif
7  difl;
8  difk;
0036 Fva2
0037 Fva3
0038 Fva4
0039 Kya1 Alarm 1 Hysteresis. Range: 0 to 9999 (0.00 to 99.99%)
0040 Kya2 Alarm 2 Hysteresis. Range: same as in kya1.
0041 Kya3 Alarm 3 Hysteresis. Range: same as in kya1.
0042 Kya4 Alarm 4 Hysteresis. Range: same as in kya1.
0043 type PV input type:
0 = J
1 = K
2 = T
3 = N
4 = R
5 = S
6 = B
7 = E
8 = Pt100
9 = 0-20 mA
10 = 4-20 mA
11 = 0-50 mV
12 = 0-5 V
13 = 0-10 V
0044 addr Communication slave address. Range: 1 to 247
0045 bavd Communication Baud-Rate:
0  1200;1  2400;2  4800;3  9600; 4  19200;
5  38400; 6  57600; 7  115200;
0046 avto Control Mode. Range: 0  manual; 1  automatic.
0047 rvn Enable control. Range: 0  no; 1  yes.
0048 act Control action. Range: 0  direct; 1  reverse.
0049 atvn Auto tune enable:
0= off;1= Fast; 2= Full; 3= Self; 4= rSLF; 5= tGHt;
0050 Bla1 Alarm power-up inhibit. Range: 0  no; 1  yes.
0051 Bla2
0052 Bla3
0053 Bla4
0054 Key Key press remote action. Range: 0 to 9
1: tecla P
2: tecla

4: tecla 
8: tecla B
9: teclas P e B
0062 A1t1 Alarm 1 Time 1. Range: 0 to 6500s.
Refer to operation manual for more details.
0063 A1t2 Alarm 1 Time 2 (in seconds).
Range: same as in a1t1.
0064 A2t1 Alarm 2 Time 1 (in seconds).
Range: same as in a1t1.
0065 A2t2 Alarm 2 Time 2 (in seconds).
Range: same as in a1t1.
0066 sfst Soft-Start time (in seconds).
Range: 0 to 9999
0067
vnit
Temperature unit. Range: 0 to 1.
0  C; 1  F.
0068 bias Bias. Range: -100 to +100%.
0070 R&S
Segment
Ramp and Soak segment being executed (read only).
Range: 0 to 9.
0071 Pr n Ramp and Soak segment to be viewed or edited.
Range: 1 to 20.
0072 E pr Ramp and Soak segment to be executed.
Range: 0 to 20.
0073 Remaining time
R&S
Indicates the remaining time of the Ramp and Soak
segment.
0074 Sqrt Square root of a linear input.
Range: 0->Disable;1->Enable.
0075 Calibration PV
Low
Enter the low input value currently applied in the PV input
for calibration purposes.
0076 Calibration PV
High
Enter the high input value currently applied in the PV input
for calibration purposes.
0077 Calib. remote
SP Low
Enter the low input value currently applied in the remote
setpoint input for calibration purposes.
0078 Calib. remote
SP High
Enter the high input value currently applied in the remote
setpoint input for calibration purposes.
0081 FLSH Enables the top display blinking as a function of the
selected alarm:
0-> Disable
1-> Enable to alarm 1
2-> Enable to alarm 2
3-> Enable to alarm 1 and 2
0086 Rstr Restores original default calibration.
Range: 0 to 1; 0-> do not restore; 1-> restore calibration