Beijer Electronics BFI-P2 V1.21 - Manual (Page 5)

User Guide Revision 1.121
www.beijerelectronics.com
5
Declaration of Conformity:
Beijer Electronics hereby states that the BFI‐P2 product range conforms to the relevant safety provisions of the Low Voltage Directive
2006/95/EC and the EMC Directive 2004/108/EC and has been designed and manufactured in accordance with the following harmonised
European standards:
EN 61800‐5‐1: 2003
Adjustable speed electrical power drive systems. Safety requirements. Electrical, thermal and energy.
EN 61800‐3 2
nd
Ed: 2004 Adjustable speed electrical power drive systems. EMC requirements and specific test methods
EN 55011: 2007 Limits and Methods of measurement of radio disturbance characteristics of industrial, scientific and
medical (ISM) radio‐frequency equipment (EMC)
EN60529 : 1992 Specifications for degrees of protection provided by enclosures
STO Function
BFI‐P2 incorporates a hardware STO (Safe Torque Off) Function, designed in accordance with the standards listed below.
Standard Classification Independent Approval
EN 61800‐5‐2:2007 Type 2
**TUV
EN ISO 13849‐1:2006 PL “d”
EN 61508 (Part 1 to 7) SIL 2
EN60204‐1 Uncontrolled Stop “Category 0”
EN 62061 SIL CL 2
** Note : TUV Approval of the “STO” function is relevant for drives which have a TUV logo applied on drive rating label.
Electromagnetic Compatibility
All drives are designed with high standards of EMC in mind. All versions suitable for operation on Single Phase 230 volt and Three Phase 400 volt
supplies and intended for use within the European Union are fitted with an internal EMC filter. This EMC filter is designed to reduce the
conducted emissions back into the supply via the power cables for compliance with harmonised European standards.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the EMC
legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with the EMC
Directive 2004/108/EC. When using a drive with an internal or optional external filter, compliance with the following EMC Categories, as defined
by EN61800‐3:2004 can be achieved:
Drive Type / Rating
EMC Category
Cat C1 Cat C2 Cat C3
1 Phase, 230 Volt Input
BFI‐P2‐x2‐xxxx‐1Fxx‐xx No additional filtering required
Use shielded motor cable
3 Phase, 400 Volt Input
IP20 & IP66 Models
BFI‐P2‐x4‐xxxx‐3Fxx‐xx Use Additional External Filter No additional filtering required
Use Shielded Motor Cable
3 Phase, 400 Volt Input
IP55 Models
ODP‐2‐x4‐xxxx‐3FxN‐xx Use Additional External Filter No Additional Filtering Required
Use Shielded Motor Cable
Note
Compliance with EMC standards is dependent on a number of factors including the environment in which the drive is installed,
motor switching frequency, motor, cable lengths and installation methods adopted
For motor cable lengths greater than 100m, an output dv / dt filter must be used, please refer to the Beijer Electronics for further
details
Vector Speed and Torque control modes may not operate correctly with long motor cables and output filters. It is recommended to
operate in V/F mode only for cable lengths exceeding 50m
All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical including
photocopying, recording or by any information storage or retrieval system without permission in writing from the publisher.
Copyright Beijer Electronics © 2013
All drives carry a 2 year warranty against manufacturing defects from the date of manufacture. The manufacturer accepts no liability for any
damage caused during or resulting from transport, receipt of delivery, installation or commissioning. The manufacturer also accepts no liability
for damage or consequences resulting from inappropriate, negligent or incorrect installation, incorrect adjustment of the operating parameters
of the drive, incorrect matching of the drive to the motor, incorrect installation, unacceptable dust, moisture, corrosive substances, excessive
vibration or ambient temperatures outside of the design specification.
The local distributor may offer different terms and conditions at their discretion, and in all cases concerning warranty, the local distributor
should be contacted first.
The contents of this User Guide are believed to be correct at the time of printing. In the interest of a commitment to a policy of continuous
improvement, the manufacturer reserves the right to change the specification of the product or its performance or the contents of the User
Guide without notice.
This User Guide is for use with version 1.20 Firmware.
User Guide 1.21
Beijer Electronics adopts a policy of continuous improvement and whilst every effort has been made to provide accurate and up to date
information, the information contained in this User Guide should be used for guidance purposes only and does not form the part of any contract.