Dwyer ULTM - Manual (Page 6)

8. SIM Card*
A Mini-SIM card must be inserted in the Series ULTM to allow use of the cellular
feature. Never insert or take out a SIM card when Series ULTM power is on. Follow
these instructions regarding your SIM card:
8.1 The SIM card must support SMS services with your local cellular operator. You
do not need any voice or browser capabilities in your cellular service.
Depending on your cellular operator – you might be required to use a USIM
card.
8.2 Deactivate the SIM PIN code if the PIN code is active before inserting in the
ULTM. Deactivation is preformed by inserting the SIM card into a cellular phone
and following the instructions of the phone manufacturer. PIN code
configuration is usually found in your phone Settings – Security Settings – PIN
Code Request or similar.
8.3 Always test your SIM card before inserting into Series ULTM. Test the SIM card
by inserting the card into a cellular phone and sending an SMS. Verify that no
PIN code is required, that the proper operator serves the cellular link and that
the SMS reaches its destination.
8.4 Turn off Series ULTM. Turn the Series ULTM top cap counter-clockwise and
expose the electrical connections board. Insert the SIM card into the proper slot
as described in the following figure. The SIM may be pulled out by pressing it
downward again. Insert as shown in Figure 9 below.
8.5 Aim Series ULTM to proper target (e.g. floor), turn on Series ULTM and closely
observe the lower status line on the display (status lines are explained in the
Operating Instructions Chapter 3- Measurement Screen sub-chapter).
You should observe the report “GSM Initializing” for 30 to 60 seconds. Then you
should observe several additional status reports including “GSM Active”. This
indicates proper SIM card operation.
*Series ULTM only supports AT&T and T-Mobile mini-SIM cards. Make sure unit will
work with carrier.
Chapter 3. Operating Instructions
This chapter describes the keypad and display of the Series ULTM. The keypad
and display add the following functionality to Series ULTM:
• Viewing measurement results and viewing information related to the system
• Configuring Series ULTM
This chapter focuses on the structure and operation of the keypad and display.
Configuration of the system via a PC is described in following chapters. Expose the
keypad by turning the cap counterclockwise all the way.
1. Keypad
1.1 Navigation Keys
Use the navigation keys to scroll through the display.
Page 5
Figure 9: SIM Card.
1. Choosing Location
Distance to Tank Walls
Flange
Acoustic Noises
Electrical Interference
Tank Installation
Sensor
External Thermistor
2. Handling Dead Zone
Extension Pipes (1)
Extension Pipes (2)
Extension Pipes (3)
3. Power Source
Voltage
Battery (Internal/External)
Ripple and Noise
Type
USB Power Source
4. Cellular Communications
SIM Card with SMS Service
Destination Phone Number
SMS Alerts
5. Measurement
Configuration
Full/Empty, Level/Distance
Filling Rate
False Echo Scan
Near Blocking Distance (NBD)
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
MUST BE
At least 11.81˝ (30 cm) from walls
+3.94/39.37˝ (+10 cm /1 m) range.
Fixed on a horizontal surface.
Far away from acoustic noises and
vibrations.
Shielded away from power and sensor
cables.
Far away from tank inlets, outlets,
physical obstacles.
Exactly perpendicular to the surface of
the target.
In shaded location, attached to the tank
body.
Of at least 3˝ (7.62 cm) internal
diameter and 5.91˝ (15 cm) above
target (from sensor face).
With completely smooth interior surface.
Installed with a flange/not protruding
into the tank.
At least 8 VDC on unit terminals.
Rated higher than 8 VDC due to
voltage drop.
Not exceeding 100 mV.
Preferably regulated switching power
supply.
Accompanied by power source for field
operations.
Inserted in the SIM card slot.
Set and formatted correctly.
Defined using correct limits.
Configured correctly.
Defined (consider the application).
Executed when the tank is empty.
Set up in flange and extension pipe
installations.
Figure 10: Navigation Keys.
9. Must Be Pamphlet