Edwards Signaling 108 Series - Manual (Page 2)

P/N 3100178 ISSUE 3
To sound tone module with a particular light source,
connect horn hot terminal to selected light terminal on
the terminal block.
b. Cat. Series 108IP or Cat. Series 108ID Using wire nuts,
connect 18" (457 mm) wire leads to field wiring. The
wire leads are marked as follows: Neutral, Red, Blue (for
models with Red, Amber and Blue LEDs) or Green (for
models with Red, Amber and Green LEDs), Amber, and
2nd Module.
5. If using a second module, install as follows (see Figure 4):
a. Loosen the captive screw in the cap and remove the cap
from the unit.
b. Pull the captive key in the second lens module into the
"out" position.
c. Place the second lens module on top of the first.
d. Push in the captive key to secure the lens module.
e. Insert the light source into board grooves at bottom of
lens module, ensuring that the four prongs on the PC
board are aligned with the plug located in the back of the
lens assembly.
NOTE: When using LED light sources, ensure that the color of
the LED light source and the lens assembly match.
f. Place the lens assembly cover on the front of the lens
module and secure using two captive screws.
g. Replace the cap on top and secure the cap with the captive
screw.
6. If using the Cat. No. 108I, set the selected tone. See Table 3
and Figure 3.
7. Apply power to the unit and verify proper operation.
Maintenance
The lens surfaces should be periodically dusted and cleaned with
a dry soft clean cloth to maintain optimum light visibility. If
necessary, the outside of the lens may be cleaned with water and a
mild detergent on a well rung-out, soft, clean cloth.
Catalog Peak Inrush Repetitive
Number Mounting Voltage Current Current Surge Current Colors
108I-RGA-N5 Pipe Mount 120V 50/60 Hz 0.115 A* 30A @ 2 µs 0.45A @ 2 ms (120 Hz) red, green, amber
108I-RBA-N5 Pipe Mount 120V 50/60 Hz 0.115 A* 30A @ 2 µs 0.45A @ 2 ms (120 Hz) red, blue, amber
108I-RGA-G1 Pipe Mount 24V DC 0.105 A* 5A @ 1 ms 0.275A @ 2 ms (500-1 kHz) red, green, amber
108I-RBA-G1 Pipe Mount 24V DC 0.105 A* 5A @ 1 ms 0.275A @ 2 ms (500-1 kHz) red, blue, amber
108IP-RGA-N5 Pipe Mount (Short Base) 120V 50/60 Hz 0.045 A 13A @ 2 µs 0.10A @ 4 ms (60 Hz) red, green, amber
108IP-RBA-N5 Pipe Mount (Short Base) 120V 50/60 Hz 0.045 A 13A @ 2 µs 0.10A @ 4 ms (60 Hz) red, blue, amber
108IP-RGA-G1 Pipe Mount (Short Base) 24V DC 0.055 A 5A @ 1 ms 55 mA red, green, amber
108IP-RBA-G1 Pipe Mount (Short Base) 24V DC 0.055 A 5A @ 1 ms 55 mA red, blue, amber
108ID-RGA-N5 Direct Mount 120V 50/60 Hz 0.045 A 13A @ 2 µs 0.10A @ 4 ms (60 Hz) red, green, amber
108ID-RBA-N5 Direct Mount 120V 50/60 Hz 0.045 A 13A @ 2 µs 0.10A @ 4 ms (60 Hz) red, blue, amber
108ID-RGA-G1 Direct Mount 24V DC 0.055 A 5A @ 1 ms 55 mA red, green, amber
108ID-RBA-G1 Direct Mount 24V DC 0.055 A 5A @ 1 ms 55 mA red, blue, amber
*The current rating for the 108I series indicates an activated tone in the multi-tone module.
Table 1. Specifications
To prevent leakage, ensure the magnifier ring on the
lens cover and the magnifier ring on the lens module
are aligned (Figure 4).
WARNING
Figure 1. Wiring
Figure 2. Wiring the Tone Module
T O N E U T R A L
O N T E R M IN A L
B L O C K
N H
S E PA R AT E H O T L E A D O R
C O N N E C T ED T O A P P R O P R IAT E
L IG H T M O D U L E T E R M IN A L
T E R M IN A L B L O C K
NE
UT
RA
L
/CO
M
M
O
N
B
L
UE
/G
RE
EN
LED
RE
D L
E
D
AM
B
E
R
L
E
D
NOT
USE
D