Watlow Series PD Ethernet Enabled Temperature and Process Controller - Manual (Page 27)

W a t l o w S e r i e s P D
■
2 5
■
A p p e n d i x
Output Types
Open Collector
• Maximum voltage: 42V Î (dc)
• Maximum current: 500 mA
• Class 2 power source required
Switched DC
• Supply voltage : 24V Î (dc) @ 30 mA
• Supply voltage maximum: 28V Î (dc) into an infi-
nite load
Solid-state Relay
• Optically isolated
• Zero cross switched
• Without contact suppression
• Minimum load current: 500 µA rms
• 0.5A at 24 to 240V
Å (ac), resistive
• 20 VA pilot duty, 120/240VÅ (ac), inductive
• Maximum offstate leakage current: 10 µA rms
• Use RC suppression for inductive loads
Electromechanical Relay, Form A
• Minimum load current: 10 mA
• 2 A @ 240V
Å (ac) or 30V Î (dc), resistive
• 125 VA pilot duty, 120/240VÅ (ac), inductive
• Electrical life 100,000 cycles at rated current
• Use RC suppression for inductive loads
Electromechanical Relay, Form C
• Minimum load current: 10 mA
• 2 A @ 240V
Å (ac) or 30V Î (dc), resistive
• 125 VA pilot duty, 120/240VÅ (ac), inductive
• Electrical life 100,000 cycles at rated current
• Use RC suppression for inductive loads
Process (Control or Retransmit)
• Range selectable: 0 to 20 mA, 4 to 20 mA, 0 to 5V Î
(dc), 1 to 5V Î (dc), 0 to 10V Î (dc) (Can reverse low
and high values.)
• Reverse or direct acting
• 0 to 10V
Î (dc) voltage output into 1,000
Ω
mini-
mum load resistance
• 0 to 20 mA current output into 800
Ω
maximum
load resistance
• Resolution:
dc ranges: 2.5 mV nominal
mA ranges: 5 µA nominal
• Calibration accuracy:
dc ranges: ±15 mV
mA ranges: ±30 µA
• Temperature stability: 100 ppm/°C
Communications
Ethernet
• Isolated
• Ethernet RJ 45 connector, 10 base T
• HTTP interface
• DHCP, auto IP or fixed IP addressing
Agency Approvals
• UL
® 508 File #102269, C-UL ® , CSA and CE
UL ® is a registered trademark of the Underwriter’s
Laboratories, Inc.
• Submitted to Canadian Standards Association for
testing.
Terminals
• Touch-safe
• Compression: Will accept 0.2 to 4 mm
2 (22 to 12
AWG) wire
• Wire strip length: 6 mm (0.24 in)
• Torque terminal blocks to 0.9. Nm (8 in-lb)
Power
• 24V
‡ (ac/dc) +10%; -15%; 50/60 Hz, ±5%
• Class 2 power source required.
• 14VA maximum power consumption
• Data retention upon power failure via nonvolatile
memory
Operating Environment
• 0 to 65°C (32 to 149°F)
• 0 to 90% RH, non-condensing
• Storage temperature: -40 to 85°C (-40 to 185°F)
Dimensions
• Width x height x depth
42 mm x 118 mm x 128 mm (1.64 in x 4.66 in x
5.06 in)
• DIN rail or chassis mount
DIN rail spec DIN 50022, 35 mm x 7.5 mm (1.38 in
x 0.30 in)
Note: These specifications are subject to change without
prior notice.