Maple Systems MAP450D User Manual
Operation manual
Operation Manual
808 134th Street SW, Suite 120
Everett, WA 98204, USA
Phone: (425) 745-3229
Fax: (425) 745-3429
E-mail: [email protected]
Web: www.maple-systems.com
1010-0101, Rev. 00
E
N
T
E
R
DELETE
CLEAR
SHIFT
#
:
,
?
%
$
=
*
/
+
-
.
SPACE
5
6
4
8
0
9
7
2
3
1
H
I
J
K
M
G
L
O
T
U
S
Q R
Y
Z
X
A
B C D
F
E
P
N
V W
Table of contents
Document Outline
- Ta ble of Con tents
- IN TRO DUC TION: Wel come 2
- CHAP TER 1: OIT Con fig u ra tion 4
- Con fig u ra tion Mode 4
- Op er ating Pa ram e ters 6
- Dis play Viewing An gle Set ting 6
- Baud Rate Set ting 6
- Par ity Set ting 7
- Data Bits Set ting 7
- Stop Bits Set ting 8
- Hand shak ing Set ting 8
- Op er ating Mode Set ting 10
- Line Ter mi na tor Set ting 10
- Ap pend Line feed Set ting 11
- Lo cal Echo Set ting 11
- Block Echo Set ting 12
- Turn-Around De lay Set ting 12
- De layed Line feed Set ting 13
- Use 3-Wire RS-485 Set ting 13
- Net work Ad dress Set ting 14
- Tab Width Set ting 14
- Cur sor Type Set ting 15
- Wrap Around Set ting 15
- Lo cal Key board Set ting 16
- Key Click Set ting 16
- Lo cal Setup Set ting 17
- Pass words Set ting 17
- CHAP TER 2: Op er ating Modes 18
- CHAP TER 3: Using the OIT™s Dis play 24
- AP PEN DIX A: Con trol Com mands 28
- Con fig u ra tion Con trol Com mands 29
- Set LCD Viewing An gle Com mand 29
- Save Con fig u ra tion Pa ram e ters Com mand 29
- Re quest Con fig u ra tion Data Com mand 29
- Dis play and Cur sor For mat Con trol Com mand 30
- Dis play For mat Con trol Com mand 30
- Key board Con trol Com mand 30
- Set Turn-Around De lay Com mand 30
- Set Tab Char ac ter Width Com mand 30
- Set Com mu ni ca tions Pa ram e ters Com mand 31
- En able Hand shak ing Com mand 31
- Set Op er ating Mode Com mand 31
- Set Line Ter mi na tor Com mand 31
- Gen eral Pur pose Con trol Com mands 31
- Dis play Con trol Com mands 33
- Con fig u ra tion Con trol Com mands 29
- AP PEN DIX B: Con trol Codes 36
- AP PEN DIX C: Ex tended Char ac ter Set 38
- AP PEN DIX D: ASCII Ta ble 40
- AP PEN DIX E: Trou ble shooting 42
- Index
- !
- A
- B
- C
- Command Terminator
- Configuration 4
- 3-Wire RS-485 setting 13
- Append Linefeed setting 11
- Baud Rate setting 6
- Block Echo setting 12
- Cursor Type setting 15
- Data Bits setting 7
- Delayed Linefeed setting 13
- Display Viewing Angle setting 6
- Handshaking setting 8
- Key Click setting 16
- Line Terminator setting 10
- Local Echo setting 11
- Local Keyboard setting 16
- Local Setup setting 17
- Network Address setting 14
- Operating Mode setting 10
- Parity setting 7
- Passwords setting 17
- Request Configuration Data control command 29
- Save Configuration Parameters control command 29
- Stop Bits setting 8
- Tab Width setting 14
- Turn-Around Delay setting 12
- Wrap Around setting 15
- Configuration Mode 4
- Control Codes 36
- Control Commands 28
- Clear Output Buffer 32
- Create Display Variable 34
- Disable Block Mode 33
- Display and Cursor Format 30
- Display Format 30
- Display Message 32
- Echo Back Text 31
- Enable Block Mode 33
- Enable Handshaking 31
- Keyboard 30
- Poll OIT Buffer 32
- Read Cursor Position 34
- Read Display Variable 33
- Request Configuration Data 29
- Request Keyboard Buffer Status 33
- Retransmit Last Keyboard Buffer 32
- Save Configuration Parameters 29
- Set Communications Parameters 31
- Set Cursor Position 34
- Set LCD Viewing Angle 29
- Set Line Terminator 31
- Set Operating Mode 31
- Set Tab Character Width 30
- Set Turn-Around Delay 30
- Sound Bell 32
- Write Display Variable 34
- Cursor
- D
- E
- H
- I
- K
- L
- M
- N
- O
- P
- S
- T
- V
- W
- Index