Ramsey Winch 300/H-300 RAM-LOK User Manual
Page 3
RAMSEY WINCH MODEL 300/H-300 SERIES
PLEASE READ THIS MANUAL CAREFULLY.
This manual contains useful ideas in obtaining the most efficient operation from your Ramsey Winch, and safety procedures one
needs to know before operating a Ramsey Winch.
WARRANTY INFORMATION
Ramsey Winches are designed and built to exacting specifications. Great care and skill go into every winch we make. If the
need should arise, warranty procedure is outlined on the back of your self-addressed postage paid warranty card. Please read
and fill out the enclosed warranty card and send it to Ramsey Winch Company. If you have any problems with your winch,
please follow instructions for prompt service on all warranty claims.
* SPECIFICATIONS: Conforms to SAE J706**
Rated Line Pull
9,000 lbs.
1st Layer
4,070 Kg
300/H-300
……………………………………………………………
60:1
346/H-346
……………………………………………………………
46:1
300/346
85 lbs (39 Kg)
H-300/H-346
110 lbs (50 Kg)
Y-300/Y-346
80 lbs (36 Kg)
HY-300/HY-346
105 lbs (48 Kg.)
1
2
3
4
lbs.
9,000
7,500
6,400
5,600
Kg.
4,070
3,390
2,890
2,530
ft.
25
60
95
140
m
8
18
30
43
ft.
15
30
55
75
m
4
9
16
22
Line Speed (FPM/MPM)
WORM RPM
1
2
3
4
300
15.0
17.9
20.8
23.7
Y-300
4.5
5.4
6.3
7.2
346
19.6
23.4
27.2
31.0
Y-346
5.9
7.1
8.2
9.4
H-300
12.6
15.1
17.5
20.0
HY-300
3.8
4.5
5.3
6.0
H-346
16.5
19.7
22.0
26.0
HY-346
5.0
5.9
6.6
7.9
……………………………………………………………
890
890
750
………………………………………………………………………………
………………………………………….……………………………………
……………………………………………………………
……………………………………………………………
……………………………………………………………
*Cable Capacity per Layer
(STD)
*Cable Capacity per Layer
("Y")
Gear Reduction
** Winch only comforms to SAE J706. For SAE qualifications for mounting angles, if applicable, consult Ramsey Engineering.
NOTE: The rated line pulls shown are for the winch only. Consult wire rope manufacturer for wire rope ratings.
Weight:
* These specifications are based on recommended 3/8 inch (9.5 mm) diameter extra improved plow steel (EIPS) wire rope or
equivalent.
LAYER OF CABLE
* Rated line pull per layer
750
3
WARNINGS
CLUTCH MUST BE TOTALLY ENGAGED BEFORE STARTING THE WINCHING OPERATION.
DO NOT DISENGAGE CLUTCH UNDER LOAD.
DO NOT LEAVE CLUTCH ENGAGED WHEN WINCH IS NOT IN USE.
STAY OUT FROM UNDER AND AWAY FROM RAISED LOADS.
STAND CLEAR OF CABLE WHILE PULLING. DO NOT TRY TO GUIDE CABLE.
DO NOT EXCEED MAXIMUM LINE PULL RATINGS SHOWN IN TABLE.
DO NOT USE WINCH TO LIFT, SUPPORT, OR OTHERWISE TRANSPORT PERSONNEL.
A MINIMUM OF 5 WRAPS OF CABLE AROUND THE DRUM BARREL IS NECESSARY TO HOLD THE LOAD. CABLE CLAMP
IS NOT DESIGNED TO HOLD LOAD.