Foredom C.TXR-2 - Manual

Parts List
C.TXR−2
Foot Control, 230V
Form DN 12/10
FOREDOM
The Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • www.foredom.net
}
Qty Description Part No. Item
1 Cover CP10852B 1
1 Trigger Switch, 250V CP11027 2
2 Screw, #6−32 x 5/16, Slotted CP10571 3
1 Fish Paper CP10525 4
1 Circuit Board CP10521 5
1 Base CP10851 6
1 Front Base Pad CP10859 7
1 Screw, #6−32 x 1" CP10856 8
1 Washer, #6 CP10862 9
1 Rear Base Pad CP10860 10
2 Strain Relief CP10003−3 12
1 Male Cordset or Substitute Option CP10541 11
1 Female Cordset CP10868 13
1 Wire 3", Brown, Tinned CP11163 14
1 Wire 3", Brown CP11162 15
Tigger Switch
5
6
1
4
3
2
AC Mal
e P
lug
to
Power
Sourc
e
BLU
GRN/YLW
GRN
(G
RN
YL
W
)
BLK
(BRN)
BRN
BRN
Wiring Diagram
Insert adjustment screw (8) through washer (9) and into post
slot and threaded insert in cover (1). Tighten with screwdriver
until cover is just touching the trigger switch pushrod. Do not
tighten the screw further to avoid pressing the Switch Pushrod
into a permanently "on" position.
Position wires around adjustment screw post so wires will not
interfere with cover travel.
Connect Wires to New Trigger Switch as shown in the
Wiring Diagram. Push wires all the way in, so that no bare wire
is exposed. On Screw Terminal 1, push the wire lead all the way
into the socket then tighten the screw firmly. Push the other wire
lead all the way into terminal 6. Pull on all the wires, making sure
they are secure. Place Switch back into Base mounting bracket.
Snap cover (1) onto hinge posts on top of rear corners of base (6).
Disconnect Foot Control from Motor and Wall Outlet.
Instructions for Removing
and Replacing Trigger Switch
Unscrew cover adjustment screw (8).
Using flat blade of screwdriver inserted at Point A
between Cover (1) and Base (6), carefully pry Cover off.
5.
Remove Trigger Switch (2) from Base mounting bracket.
On older Switches, all the terminals will be push-in, spring clamp
type. On newer Switches, some terminals have screw fasteners.
To remove wires from the push-in terminals, insert 1.3mm [.05in]
approximate diameter pin or the blade of a jeweler's screwdriver
all the way into the terminal socket to release the spring clamp.
Grasp the tool and wire and pull them together out of the socket.
If you have difficulty removing the wires from the push-in terminals
and you have wire-cutting, stripping, and soldering tools, you can
cut the wires off where they exit from the terminals. To prepare
the cut wires for installation into the replacement Switch, strip
them back exactly 8.25 mm [5/16 in], then apply solder to the
stripped ends to fuse the strands together.
4.
3.
6.
7.
8.
2.
1.
Fe
mal
e Receptacle
to
Motor
For use with LX 230V Motors
and discontinued TX 230V Motors.
Cordset Option Part No. Cordset Descrption
CPOption20 CP10545 No Plug, Europe
CPOption21 CP10553 Male, United Kingdom
CPOption22 CP10554 Male, Continental Europe
CPOption25 CP10555 Male, India 10A
CPOption26 CP10556 Male, Australia
1
2
3
4
5
6
7
8
9
10
11
11 13
BRN
WHT
(BLU)
Point A
14
15