Foredom H.10D User Manual
Important instructions, For foredom, Handpieces h.10 and h.10d

Attach Handpiece to Flexible Shaft
1.Before attaching the handpiece, connect the motor to
the speed control and plug into power source.
2. While holding the black colored metal outer sheath tip
facing upward, turn on the control so that the motor is
running at about half speed and then turn it off.
3. While the inner key tip is still rotating, grip the handpiece
and push it onto the sheath tip with one firm motion until it
snaps into place (shown at right).
4. This will align the key tip into the keyway slot (shown
above).
5. To verify this, insert and tighten an accessory into collet
or chuck, turn on control to a low speed and observe that
the accessory rotates smoothly.
Note: Handpiece can run only with 2.35mm (3/32
″)
shank bur inserted.
Do not operate with lever in open position— this will
cause the handpiece to lock up.
Attaching Accessories
1. To Insert Bur Move Lever 180º clockwise towards the
For Foredom
®
Handpieces H.10 and H.10D
Please read these safety instructions
thoroughly before operating this tool. They
are for your protection and should always be
followed to reduce the risk of personal injury
or damage to the handpiece.
Always use a proper dust collection system or
wear a respirator to prevent the inhalation of
dust particles, or other debris into the lungs.
IMPORTANT INSTRUCTIONS
Form 1243 n 12/12 Printed in U.S.A.
Safety Instructions
Always wear proper eye and face protection.
Wear safety glasses or a face shield whenever you oper-
ate a Foredom Flexible Shaft machine or any power tool
to prevent serious eye injury.
Never use or continue to use any rotary accessory that is
damaged, bent, loose, vibrating or out of balance. Inspect
each accessory for cracks or flaws before using it.
Do not wear loose fitting clothing or jewelry. Loose
clothing or jewelry can become entangled in the tool. Do
not wear items such as neckties, necklaces, or bracelets
when operating power tools. Secure or tie back long hair.
Always use a proper dust collection system or wear a
respirator to prevent the inhalation of dust particles, or
other debris into the lungs.
Adjust the Shaft and Sheath
It is important to check the sheath and shaft tip and properly
adjust them before attaching this handpiece to your
Foredom flexible shaft tool.
The tip of the flexible shaft should extend 3/4
″ beyond the
end of the sheath. This adjustment is made by loosening the
set screw in the motor connector and moving the sheath in
or out while the motor and shaft and sheath are hanging
fully extended or laying on a flat surface. When the shaft is
adjusted correctly, tighten the set screw in the
motor connector.
Keyway
Key Tip on end of shaft
Inside
back end
of handpiece
See your Power Tool Owner's Manual for
complete instructions on use, care
and maintenance.
Wear safety glasses or a face shield whenever
you operate a Foredom Flexible Shaft machine
or any power tool to prevent serious eye injury.
IMPORTANT!
To Remove Handpiece from Flexible Shaft
1. First make sure your power tool
is unplugged.
2. To remove, simply pull the handpiece off
the shaft and sheath with a firm grip.
Always make sure your power tool is unplugged
during any maintenance procedure.
Keep a 2.35mm (3/32
″) shank bur in the handpiece at
all times during operation and storage.
Never use a damaged, bent, vibrating, or out of balance
accessory or other tool bit. Inspect each accessory for
cracks or flaws before using.
Never change accessories while motor switch is in
the ON or FOR (forward) or REV (reverse) position.
Secure the workpiece that you are carving in a vise or
other work holding device. Holding it with your hand is
dangerous and can result in serious hand injury.
Keep both hands and fingers away from the cutting edge
at all times.
Never wear open shoes or sandals. Use footwear that is
tough enough to protect your feet from falling tools.
Never cut or exert pressure toward your hand or any other
part of your body.
Do not wear loose fitting clothing or jewelry. Loose
clothing or jewelry can be come entangled in the tool. Do
not wear items such as neckties, necklaces, or bracelets
when operating power tools. Secure or tie back long hair.
Let the speed of the tool do the work.
For More Information
For more information on Foredom machines,
handpieces, or accessories, contact your local dealer.
When no local dealer is available, contact:
The Foredom Electric Co.
16 Stony Hill Road
Bethel, CT 06801 or call (203) 792-8622 visit our
website at www.foredom.net