Fluid Components International FS10A - Manual (Page 5)

FS10 Series
Fluid Components International LLC 3
Instrument
ƒ Media Compatibility
All gases and liquids compatible with 316L stainless steel and
hastelloy C22.
ƒ Process Connection
1/4” NPT; compatible with 1/4”, 3/8” and 1/2” tube tee,
1/4” tube tee with 1/8” injection tube adapters and SP76 adapter
(FCI part number 019897-01)
ƒ Flow Sensitivity/Range:
Air / Gas Liquids
CC / Min SCFH CC / Min GPH
Min Max Min Max Min Max Min Max
1/8” tube adapter with
0.0625” ID injection tube 10
2,000 0.02 5 0.70 18.00 0.01 0.30
1/8” tube adapter with
0.0940” ID injection tube 25
5,000 0.05 10 1.50 40.00 0.03 0.60
1/4” tube tee 50 20,000 0.10 40 4.00 100.00 0.07 1.70
SP76 adapter 50 20,000 0.10 40 4.00 100.00 0.07 1.70
3/8” tube tee 180 50,000 0.40 100 14.00 350.00 0.20 5.50
1/2” tube tee 375 100,000 0.80 200 30.00 750.00 0.50 12.00
ƒ Repeatability:
± 0.5% of reading
ƒ Temperature Coefficient
For temperatures > ± 30 °F [± 16 °C]
Gas: Maximum ± 0.025% of reading/°F up to 500 °F
[± 0.05% of reading/°C up to 260 °C]
Liquid: Maximum ± 0.2% of reading/°F up to 250 °F
[± 0.367% of reading/°C up to 121 °C]
Turndown Ratio: 5:1 to 100:1
Agency Approvals
FM, FMc: Nonincendive, Class I Division 2 Groups A, B, C, D;
Class II, Division 2 Groups E, F, G; Class III,
T4@Ta=71°C Type 4X
ATEX, IEC: Nonincendive for gas and dust, Zone 2
II 3 G Ex nA IIC T4 Gc
II 3 D Ex tc IIIC T 81°C Dc
IP64
CE Mark
Flow Element
Materials of Construction (Wetted parts) 316L stainless steel with
Hastelloy C-22 thermowells; optional, all Hastelloy-C22 probe
assembly
Operating Temperature
Standard: -40 °F to 250 °F [-40 °C to 121 °C]
Optional: -40 °F to 500 °F [-40 °C to 260 °C]; remote configuration
only
Operating Pressure
Tube tee fitting: 500 psig [34 bar (g)]
SP76 adapter: Per SP76 manifold specifications up to 500 psig
[34 bar (g)] maximum
Transmitter/Electronics
ƒ Enclosure
NEMA 4X [IP64], anodized aluminum
ƒ Operating Temperature
-40 °F to 160 °F [-40 °C to 71 °C]
ƒ Output Signals
Standard:
(1) Relay (SPDT, 1A @ 24 Vdc); [1A @ 24 Vdc / 120 Vac, FM and
FMc only] or (1) Open Collector N-Channel MOSFET (100 mA);
(1) 4-20 mA * (500 Ω max. load). User scalable, general purpose,
un-calibrated output proportional to flow rate for trend monitoring.
(1) RS232C Serial I/O
(For linearized, calibrated analog outputs see FCI thermal mass
flow meter products)
* Fault indication per NAMUR NE43 guidelines, user selectable
high (> 21.0 mA) or low (< 3.6 mA)
Other Digital Comms: Contact FCI
ƒ Display
10 LED array, red; sequential lighting proportional to flow trend and
flashes at setpoint
ƒ User Interface
Two top-mounted push buttons to program switch/trip point, zero and
span setting, relay hysteresis and time delay; button operation may
be user disabled to prevent unwanted changes; all set-up functions
also programmable via RS232C port
ƒ Input Power
24 Vdc (21.5 Vdc to 30 Vdc); maximum 2.5 watts
ƒ Remote Configuration
Transmitter/electronics may be remote-mounted from flow element
using interconnecting cable; remote flow element available with
potted cable in 6’, 15’ or 30’ [2m, 5m or 10m] length and M12 con-
nection plug at electronics; optional extended temperature service to
500 °F [260 °C] with selection of PTFE jacketed cable.
Technical Specification