AMX Mio Modero R-4 - Manual (Page 62)

Programming the Mio R-4
54 Mio Modero R-4
"^" Button Commands (Cont.)
^BMF
Set any/all button
parameters by
sending

embedded codes
and data
Set any/all button parameters by sending embedded codes and data.
Syntax:
"'^BMF-,,'"Variables: • variable text address char array = 1 - 4000.• button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons1 = Off state and 2 = On state).• level range = 1 - 600 (level value is 1 - 65535).• data: • ’%B’ = Set the border style name. See theBorder Styles by Numbers table on page 38.• ’%B’, = Set the borer style number. See theBorder Styles by Numbers table on page 38.• ’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top. Refer to the ^BDO command on page 52 for more information.• ’%F’, = Set the font.• ’%F’ = Set the font.• ’%MI’ = Set the mask image. Refer to the ^BMI command on page 55 for more information.• ’%T’ = Set the text using ASCII characters (empty is clear).• ’%P’ = Set the picture/bitmap filename (empty is clear).• ’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are assigned in the TPDesign4 Resource Manager tab - Slots section).• ’%I’ = Set the icon using values of 01 - 9900 (icon numbers are assigned in the TPDesign4 Resource Manager tab - Slots section).• ’%J’, = As shown the following telephone keypad alignment chart: • ’%JT’ = As shown the above telephone keypad alignment chart, BUT the 0 (zero) is absolute and followed by ’,,’• ’%JB’ = As shown the above telephone keypad alignment chart BUT the 0 (zero) is absolute and followed by ’,,’• ’%JI’ = As shown the above telephone keypad alignment chart, BUT the 0 (zero) is absolute and followed by ’,,’• '%R,,,' = Set rectangle.1478963250Zero can be used for an absolute position
Variables:
• variable text address char array = 1 - 4000.
• button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons

1 = Off state and 2 = On state).
• level range = 1 - 600 (level value is 1 - 65535).
• data:
• ’%B’ = Set the border style name. See theBorder Styles by Numbers table
on page 38.
• ’%B’, = Set the borer style number. See theBorder Styles by
Numbers table on page 38.
• ’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 52 for more information.
• ’%F’, = Set the font.
• ’%F’ = Set the font.
• ’%MI’ = Set the mask image. Refer to the ^BMI command on page 55 for
more information.
• ’%T’ = Set the text using ASCII characters (empty is clear).
• ’%P’ = Set the picture/bitmap filename (empty is clear).
• ’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
• ’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
• ’%J’, = As shown the following telephone keypad alignment
chart:
• ’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
• ’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’
• ’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
• '%R,,,' = Set rectangle.
1
4
7 8 9
6
3 2
5
0
Zero can be used for an absolute position