Atec Anritsu_MT8801C - Manual (Page 17)

17
Frequency range:
869.01 to 893.97 MHz (30 kHz step, IS-95A), 1930.00 to 1989.95 MHz (50 kHz step, J-STD-008),
832.0125 to 833.9875 MHz, 843.0125 to 845.9875 MHz, 860.0125 to 869.9875 MHz (12.5 kHz step, ARIB STD-T53)
1805.05 to 1870.00 MHz (50 kHz step, KORER-PCS)
Level setting range:
–18 to –133 dBm (Main, AWGN off), +2 to –133 dBm (AUX, AWGN off)
Signal generator –24 to –133 dBm (Main, AWGN on), –4 to –133 dBm (AUX, AWGN on)
Relative level accuracy: ±0.2/20 dB (18˚ to 28˚C)
∗
Relative level accuracy at level change in time response of open-loop power control
Waveform quality: ρ Ͼ 0.99 (pilot channel: 0 dB)
Channel level accuracy: ±0.2 dB (relative level accuracy between any 2 channels)
AWGN level accuracy: ±0.2 dB (relative level for forward traffic channel)
Reception measurement FER measurement: FER measurement value, error frame number, test frame number, confidence limit pass/fail
Frequency range:
824.01 to 848.97 MHz (30 kHz step, IS-95A), 1850.00 to 1909.95 MHz (50 kHz step, J-STD-008),
887.0125 to 888.9875 MHz, 898.0125 to 900.9875 MHz, 915.0125 to 924.9875 MHz (12.5 kHz step, ARIB STD-T53)
1715.05 to 1780.00 MHz (50 kHz step, KORER-PCS)
Modulation analysis
Level range: +40 to –20 dBm (average power within a burst, main connector only)
Waveform quality: Measurement range: 0.9 to 1.0, measurement error: ±0.003 (after executing adjust range)
Residual vector error:
Ͻ 5% (after executing adjust range)
Power measurement (IF level meter)
Measurement range: +40 to –50 dBm
Measurement accuracy:
±0.4 dB (+40 to 0 dBm, after executing power meter calibration)
Transmission ±0.4 dB (+40 to –10 dBm, after executing power meter calibration, 18˚ to 28˚C)
measurement ±0.7 dB (+40 to –10 dBm, after executing internal oscillator calibration, 18˚ to 28˚C)
Linearity: ±0.1 dB (0 to –10 dB), ±0.2 dB (–10 to –20 dB), ±0.5 dB (–20 to –40 dB)
∗
Referred to reference level: Ն –10 dBm
Input connector: Main connector only
Occupied bandwidth measurement
Level range: 0 to +40 dBm (average power within a burst, MAIN connector)
–20 to +20 dBm (average power within a burst, AUX connector)
Spurious close to the carrier measurement
Level range: 0 to +40 dBm (average power within a burst, MAIN connector)
–20 to +20 dBm (average power within a burst, AUX connector)
Measurement range: Ն 50 dB (900 kHz offset), Ն 60 dB (1.98 MHz offset)
Spurious measurement
Level range: 0 to +40 dBm (average power within a burst, MAIN connector)
–20 to +20 dBm (average power within a burst, AUX connector)
Measurement range: Ն 60 dB
Functions: Registration, origination, termination, conversation, loopback, hard handoff, disconnection from
Call processing
network, disconnection from mobile station, CDMA ➞ analog handoff (IS-95A), soft handoff
(MX880201A-01), softer handoff (MX880201A-01)
Protocol: IS-95A (CDMA, analog), J-STD-008, ARIB STD-T53
◆ Option 12: CDMA Measurement (extracts)