Atec Anritsu_MT8801C - Manual (Page 13)

13
Specifications
Frequency range 300 kHz to 3 GHz
Maximum input level +40 dBm (10 W, MAIN connector), +20 dBm (100 mW, AUX connector)
MAIN I/O connector
Input/output connector
Impedance: 50
Ω
, N-type
VSWR: Յ 1.2 ( Յ 2.2 GHz), Յ 1.3 ( Ͼ 2.2 GHz)
AUX input/output connector: TNC-type
Frequency: 10 MHz
Starting characteristics:
Յ 5 ✕ 10 -8 /day (after 10 minutes of warm-up, referred to frequency after 24 hours warm-up)
Reference oscillator
Aging rate: Յ 2 ✕ 10 -8 /day, Յ 1 ✕ 10 –7 /year (referred to frequency after 24 hours warm-up)
Temperature characteristics: Յ 5 ✕ 10 –8 (0° to 50°C, referred to frequency at 25°C)
External standard input: 10 MHz or 13 MHz (±1 ppm), input level: 2 to 5 Vp-p
Frequency range: 300 kHz to 3 GHz
Power meter
Level range: 0 to +40 dBm, –10 to +40 dBm (CDMA measurement)
Level accuracy: ±10% (0 to +40 dBm, after zero-point calibration),
±10% (–10 to +40 dBm, 18° to 28°C, at average value, after zero-point calibration)
Frequency
Range: 300 kHz to 3 GHz
Resolution: 1 Hz
Accuracy: Reference frequency accuracy ±100 mHz
Output level
Level range (no modulation or analog modulation): –13 to –133 dBm (Main), +7 to –133 dBm (AUX)
Level accuracy: ±1 dB (10 MHz to 2.2 GHz,
Ն –123 dBm, 18° to 28°C), ±3 dB (10 MHz to 2.2 GHz, Ն –133 dBm),
±2 dB ( Ͼ 2.2 GHz, Ն –123 dBm, 18° to 28°C), ±4 dB ( Ͼ 2.2 GHz, level: Ն –133 dBm)
Radiated interference:
1 µV/50 Ω (carrier frequency measured, 25 mm from front panel with two-turn 25 mm diameter loop antenna)
Signal purity
Spurious: Յ –50 dBc (at CW, offset frequency 100 kHz to Յ 50 MHz; where carrier frequency: other than 1300 to
1400 MHz and 2000 to 2100 MHz), Յ –40 dBc (for all band)
Harmonics: Յ –25 dBc (at CW)
Display: Color TFT-LCD, 7.8 size , 640 ✕ 480 dots
Hard copy: Enables data hard copy of the display through a parallel interface (applicable only for EPSON VP
series or equivalent)
GPIB: This equipment is specified as a device, can be controlled from external controller (excluding power switch
and FD ejection key). No controller function
Others
Interface: SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, C0, E2)
Parallel
Conform to the Centronics. Outputs printing data to printer. Data line exclusive for output: 8
Control line: 4 (BUSY, DTSB, ERROR, PE)
Connectors: D-sub 25 pins, female (equivalent to the connector of IBM-PC/AT built-in printer)
RS-232C: All functions except power switch controlled by external controller
(baud rate: 1200, 2400, 4800, 9600 bps)
Dimensions and mass 426(W) ✕ 221.5(H) ✕ 451(D) mm, Յ 22 kg
Power 100 to 120/200 to 240 Vac (automatic voltage switch system), 47.5 to 63 Hz, Յ 300 VA
Operating temperature 0° to 50°C
EMC
EN61326: 1997/A1: 1998 (Class A),
EN61000-3-2: 1995/A2: 1998 (Class A)
EN61326: 1997/A1: 1998 (Annex A)
LVD EN61010-1: 1993/A2: 1995 (Installation Category II , Pollution degree2)
◆ MT8801C
Signal generator
Frequency range: 10 MHz to 3 GHz
Output level range: –133 to –13 dBm (MAIN connector), –133 to +7 dBm (AUX connector)
FM deviation: 0 to 40 kHz (resolution: 10 Hz)
Accuracy: Set value ±5% ±1 digit (internal modulation frequency: 1 kHz, excluding residual FM)
Internal modulation: 20 Hz to 20 kHz
RF signal generator
External modulation: 20 Hz to 20 kHz (limited to 1 Vpeak into 600 Ω )
Flatness: ±0.5 dB (referenced to 1 kHz between 0.3 to 3 kHz with 4 kHz deviation)
±1 dB (referenced to 1 kHz between 20 Hz to 20 kHz with 4 kHz deviation)
Distortion: Յ –50 dB (internal modulation frequency: 1 kHz, demodulation bandwidth: 0.3 to 3 kHz, frequency
deviation: 5 kHz)
Frequency range: 20 Hz to 20 kHz, Setting resolution: 0.1 Hz, Accuracy: Same as reference oscillator
Output
AF Generator
Level range: 0.1 mVrms to 3.0 Vrms (EMF, MAIN output impedance: 600
Ω
)
0.1 mVrms to 0.3 Vrms (EMF, MAIN output impedance: 50
Ω
)
Setting resolution: 1 µV (output level: Ͻ 4 mV), 10 µV (output level: Ͻ 40 mV)
100 µV (output level: Ͻ 0.4 V), 1 mV (output level: Յ 3 V)
◆ Option 01 (Analog Measurement)