Required tools, Adjusting the door angle – Extron Electronics MLM-WB+ User Manual
Page 14
MLM-WB+ • Installation
8
Required Tools
To install the MLM-WB+ you need the following tools:
•
Phillips screwdriver
•
Pencil
•
Flat head screwdriver
•
3/8-inch wrench or ratchet
•
Drill with drill bits
•
Wire cutter
•
Level
Adjusting the Door Angle
Before mounting the MLM-WB+, ensure that the door opens to a 90º angle. To adjust the
door angle:
1.
Set the MLM-WB+ upright on a flat surface and open the door.
CAUTION: Risk of Bodily Injury: If not properly secured in place, the
MLM-WB+ can potentially fall forward.
2.
Remove the screws holding the clevis brackets to the door.
3.
Slide the clevis brackets:
•
Forward, to make the door open to a higher position, or
•
Backward, to make the door open to a lower position.
Figure 7.
Sliding the Clevis Brackets to Adjust the Door Angle
4.
Align the holes on the clevis bracket with the holes on the door.
5.
Replace the screws that were removed in step 2.
- AVTrac Corner Cut Solution (2 pages)
- AVTrac Demonstration Kit (2 pages)
- AVTRac End Ramp and Cable Pass-Through Kits (1 page)
- AVTrac Extension Kit (15 pages)
- 1U and 2U Rack Plate (1 page)
- Under-Desk Mounting Bracket (1 page)
- AAP Wiring Guide 68-1054-01 (1 page)
- AAP Wiring Guide 68-1052-01 (1 page)
- AAP Wiring Guide (XLR connectors) (1 page)
- AAP 314 (1 page)
- AAP 301 (1 page)
- AAP Wiring Guide 68-1055-01 (1 page)
- AAP Wiring Guide 68-1058-01 (1 page)
- AAP Wiring Guide 68-1059-01 (1 page)
- AAP-MAAP Rev. A (1 page)
- AAP-MAAP Rev. D (1 page)
- MD Floor Box AAP Bracket Kit AAP 100 MD (1 page)
- AC 100 Power Module Series (1 page)
- AAP 103 Extron Ackerman AKM UK Faceplate Kit (1 page)
- ACMP 100 (2 pages)
- Active Audio AAP (1 page)
- AKM UK Series (4 pages)
- Audio AAP Wiring Guide (1 page)
- Audio Connector Rev. A (2 pages)
- Audio Connector Rev. G (1 page)
- AVTrac Extra Channel Kit (2 pages)
- AVTrac Raceway Transition (2 pages)
- AVTrac Retrofit Transition Adapter (2 pages)
- AVTrac Trim Ring-Rough-in Adapter (2 pages)
- AVTrac Above Floor (1 page)
- BB 1 (2 pages)
- BB 1000M (2 pages)
- BB 700M (2 pages)
- BB 710M (2 pages)
- Blank Rack Panel (1 page)
- BNC to 15-Pin HD (1 page)
- BNC-5 RC Termination (1 page)
- Cable Cubby 1200 (6 pages)
- Cable Cubby 200 (18 pages)
- Cable Cubby 300C (27 pages)
- Cable Cubby 500 (6 pages)
- Flexible Conduit Kit (2 pages)
- Cable Cubby Lid and Trim Ring Replacement Kit (for 300C, 300S, 600, 800) (1 page)
- Cable Cubby Setup Guide (4 pages)
- Cable Cubby Single Space AAP Bracket Kit (1 page)