Extron Electronics FOX II T_R DP User Guide User Manual
Page 29
Command/response table for Transmitter SIS commands (continued)
FOX II DP Transmitter and Receiver • Remote Control
23
Command
SIS Command
(host to unit)
Response
(unit to host)
Additional description
Status requests
View link 1 (Tx-to-Rx) status
1S
X1#]
View link 2 (Rx-to-Tx) status
2S
X1#]
View input video status
3S
X1#]
View input audio status
4S
X1#]
View all signal status
5S
SigI
X1#
•SigO
X1#
•HDCPI
X1$
•HDCPO
X1%]
Report the status of the DisplayPort input,
DisplayPort output, HDCP encoding on the input,
and HDCP encoding on the output.
View DisplayPort signal
status
6S
SigI
X1#
•SigO
X1#]
Report the status of the DisplayPort input and
DisplayPort output.
View HDCP status
7S
HDCPI
X1$
•HDCPO
X1%]
Report the status of the HDCP encoding on the
input and HDCP encoding on the output.
View temperature
20S
X1^
F•
X1^
C
]
Show temperature in degrees Fahrenheit and
Celsius.
Information requests
Information request
I
1Lnk
X1#
•2Lnk
X1#
•Vid
X1#
•Aud
X1#
•
X1&
•Tx
]
The unit responds with the current status
(signal detected) of optical link 1, optical link 2,
the video input, and the audio link; the fiber optic
transmission mode (singlemode or multimode);
and the device type (
Tx
).
Show firmware version
Q
X1*]
Example:
Q
1.23
]
The factory-installed firmware version is 1.23
(sample value only).
Request part number
N
60–
nnnn
–
nn
]
See the Extron website,
www.extron.com
, for
part numbers.
Input sync detection
E
1LS
}
X1(
horizontal
,
X1(
vertical
]
Shows horizontal frequency in kHz and vertical
frequency in Hz. 000.0,000.0 if no signal is
detected.
Request SFP status
40S
X2)
•
X2!
Tx
•
X2!
Rx
•
X2@]
Request switch position
E
STAT
}
EdidMdr
X2#]
Resets
Reset audio
E
ZA
}
Zpa
]
Reset audio setting to default levels (0 dB gain).
System reset
E
ZXXX
}
Zpx
]
Reset all settings to factory defaults.
KEY:
X1#
= Link status
0 = light or signal input not detected
1 = light or signal detected
X1$
= Input HDCP signal
0 = no source detected
1 = source detected with HDCP
2 = source detected but no HDCP present
X1%
= Loop-through display
0 = no sink device connected
1 = sink device detected and HDCP compliant
2 = sink device detected, but not HDCP compliant
X1^
= Temperature
nnn
X1&
= Transmission mode
SM = singlemode
MM = multimode
X1*
= Firmware version
v.vv
X1(
= Sync frequency
xxx.x (frequency in kHz [H] or Hz [V])
X2)
= Optical module manufacturer
Up to 16 alphanumeric characters
X2!
= Tx or Rx power
xx.x dBm
X2@
= Operating temp of module
nnn.n
X2#
= EDID switch position
00 (0 hex) through 15 (F hex) (see