Extron Electronics DSC 301 HD User Guide User Manual
Page 41
Command
ASCII Command
(host to scaler)
Response
(scaler to host)
Additional Description
AFL
Disable AFL
E
OGLOK}
Glok0]
Disables global input lock/AFL
(default).
Enable input lock
E
1GLOK}
Glok1]
Locks the output refresh rate to the
refresh rate of the selected input.
View AFL setting
E
GLOK}
X3*]
View the current input lock/AFL
setting.
View AFL status
E
41STAT}
X3(]
41Stat•X3(]
View the current input lock/AFL status.
(verbose mode response)
Video signal presence
View signal presence
E
0LS}
X3%
*X3%*X3%
]
Input 1*2*3.
On-Screen menu configuration
Menu time-out
NOTE:
Setting the time-out to 501 disables the OSD time-out (never times out). Setting the time-out to 0 disables the OSD.
Set menu time-out
E
X2!
MDUR}
MdurX2!
]
Set the OSD to X2! seconds
View time-out
E
MDUR}
X2!
]
View time-out settings
Reset commands
Reset all device
settings to factory
default settings
24
E
ZXXX
}
Zpx
]
Information request
General information
I/i
Vid
X!
•Typ
X#
•Std
X1)
•Blk
X2^
•Hrt
X1@
•Vrt
X1@]
Query firmware
version
Q/q
x.xx
]
View firmware version.
Query full firmware
version
*Q/*q
x.xx.xxxx
]
View full firmware version details.
Query Boot Loader
version, factory
firmware version,
and current
firmware version.
0Q
x.xx-x.xx.xxxx-x.
xx.xxxx
]
View boot loader version, view factory
firmware version, view current firmware
version.
Query part number
N/n
60-1253-01
]
View part number.
View internal
temperature
E
20STAT
}
Stat20•
X1!]
Temperature in degrees Celsius.
NOTE:
X!
= Input selection: 1 to 3
X#
= Input video format: 1 = RGB, 2 = YUV, 3 = Composite, 4 = HDMI
X1)
= Input standard output selection: 0 = No signal detected, 1 = NTSC 3.85, 2 = PAL, 3 = NTSC 4.43, 4 = SECAM
- = N/A (occurs when input is an active RBG, YUV [but not NTSC/PAL], or an HDMI signal)
X1!
= Internal temperature (in degrees Celsius)
X1@
= Horizontal and vertical frequencies (format is three-digit with single decimal and leading zeros for example, 075.3
X2!
= On-screen menu time-out: (default = 60 seconds), output sync time-out (default = 501 - never),
0 = OSD never displayed and output sync is instantly disabled with no active input,
1 to 500, in 1 second increments,
501 = OSD never times out/output sync never times out
X2^
= Video mute; 0 = Off or disable, 1 = On or enable (mute to black), 2 = mute all output sync and video
X3%
= Video signal status: 0 = Video or TMDS not detected, 1 = Video/TMDS detected
X3*
= Input AFL: 0 = Disabled (default), 1 = Input signal AFL enabled. See
on page 25
for variable details.
X3(
= Input AFL status: 0 = Input signal lock disabled, 1 = Input signal lock enabled, but cannot lock to applied input signal.
2 = Input signal lock enabled, output locked to applied input signal. See
on page 25 for variable details.
DSC 301 HD • SIS Communication and Control
35