Theatre Solution Jury Base Seating - Manual (Page 60)

Jury Base Seating Specifications 59
Jury Base Seating Specifications
(This section pertains to the Teatro Jury Base Seating model.)
PART 2 – PRODUCTS
2.1 SEATING
A. Provide from Theatre Solutions, Inc., 121 Park Avenue, Quakertown, PA 18951, the Teatro Jury Base
Seating as follows:
1. Basic floor-mounted Jury Base Forum chair.
B. Model noted is based on the Theatre Solutions, Inc. Teatro Jury Base Seating with the intent of
establishing the high level of quality required for the project. Other brands submitted for approval will be
given consideration provided that a full seating mock-up, along with a complete list of specification
discrepancies between the proposed substitution and the product specified is received at least 10 working
days prior to the bid date.
1. By offering a quote for this project, the bidder assumes full responsibility for complying with the
specifications for this project and shall be totally responsible for any expenses incurred if the
product quoted does not comply with the specifications.
C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for
disqualification.
2.2 MATERIALS
A. Padding material shall be flame retardant polyurethane foam which conforms to the standards of the
California Bureau of Home Furnishings 117-75.
B. Seating fabric shall be _______________________________________________ with the color to be
selected from the standard choice of colors. All upholstery shall be first quality without creases, stretch
lines, or wrinkles.
2.3 FABRICATION, GENERAL
A. Fabricate the seating for maximum comfort using materials that are carefully selected to be free from
defects, objectionable projections, or irregularities. Smooth round corners and edges to present the least
possible snagging and pinching hazards.
2.4 MOUNTING
A. The floor base shall be cast aluminum with a durable powder-coated finish. The base shall include four
countersunk holes equally spaced around the perimeter of the base for mounting to the floor with 1/4” flat
head screws, providing a flush, unobtrusive appearance.
2.5 CHAIRS
A. Chair shall be TSI model Teatro.
B. Frame Assembly: Shall consist of two legs, two armrest support plates, one base plate, and one wedge box
all welded into one integral structure upon which the seat, back, and armrests are assembled. The legs
shall be laser-profiled 5/16” thick hot-rolled steel plate upon which there is an 11 gauge armrest support
plate. The wedge box shall be formed from 11 gauge hot-rolled pickled-in-oil steel. The entire welded
assembly shall be powder-coated.
C. Seat Construction: The seat panel shall be 5/8” thick, electronically glued curved hardwood plywood. The
padding material shall be 3” thick polyurethane foam, shall be glued to the inner surface of the seat panel,
and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117. The seat shall be
attached to the frame assembly with (4) 1/4-20 x 1” pan head machine screws and split lock washers.
D. Back Construction: The back panel shall be 3/8” thick, electronically glued curved hardwood plywood. The
padding material shall be 1-3/4” thick, 2-3/4” thick in the lumbar region, shall be glued to the inner surface
of the back panel, and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117.
The outside surface of the back panel shall be encapsulated in 1/4” thick slab polyurethane foam. The
back shall be attached to the frame assembly using (2) 1/4-20 x 3/4” flat head machine screws and (2)
3/8-16 x 1-1/4” flat head machine screws.
E. Armrests: Shall be kiln-dried hardwood, nominally 1” thick x 2-1/2” wide x 11-3/4” long. Each armrest will
be fastened to the frame assembly with (4) #8 x 5/8” pan head sheet metal screws.
F. The chair shall be equipped with a non-tilt mechanism.
G. The chair shall be equipped with a swivel and return cylinder.