Theatre Solution Jury Base Seating - Manual (Page 56)

Jury Base Seating Specifications 55
Jury Base Seating Specifications
(This section pertains to the Acclaim Jury Base Seating model.)
PART 2 – PRODUCTS
2.1 SEATING
A. Provide from Theatre Solutions, Inc., 121 Park Avenue, Quakertown, PA 18951, the Acclaim Jury Base
Seating as follows:
1. Basic floor-mounted Jury Base Acclaim chair.
B. Model noted is based on the Theatre Solutions, Inc. Acclaim Jury Base Seating with the intent of
establishing the high level of quality required for the project. Other brands submitted for approval will be
given consideration provided that a full seating mock-up, along with a complete list of specification
discrepancies between the proposed substitution and the product specified is received at least 10 working
days prior to the bid date.
1. By offering a quote for this project, the bidder assumes full responsibility for complying with the
specifications for this project and shall be totally responsible for any expenses incurred if the
product quoted does not comply with the specifications.
C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for
disqualification.
2.2 MATERIALS
A. Padding material shall be flexible polyurethane foam which conforms to the standards of the California
Bureau of Home Furnishings 117-75. The back shall be 2” thick. The seat shall be 3” thick.
B. Seating fabric shall be _______________________________________________ with the color to be
selected from the standard choice of colors. The inner back and seat shall be upholstered by attaching the
fabric to the inside wood back and seat panels. All upholstery shall be first quality without creases, stretch
lines, or wrinkles.
2.3 FABRICATION, GENERAL
A. Fabricate the seating for maximum comfort using materials that are carefully selected to be free from
defects, objectionable projections, or irregularities. Smooth round corners and edges to present the least
possible snagging and pinching hazards.
2.4 MOUNTING
A. The Jury Base shall be cast aluminum with a durable powder-coated finish. The base shall include four
countersunk holes equally spaced around the perimeter of the base for mounting to the floor with 1/4” flat
head screws, providing a flush, unobtrusive appearance.
2.5 CHAIRS
A. Chair shall be TSI model Acclaim.
B. Frame Assembly: Shall consist of two vertical support tubes, two frames, and one plate all welded into one
integral structure upon which the seat, back, and armrests are assembled. The vertical support tubes shall
be 3/4” x 2” x 16 gauge seamless steel tubing. The frame shall be 1/4” thick x 2” wide hot-rolled steel. The
entire assembly shall be powder-coated.
C. Seat Construction: The seat panel shall be 3/4” thick, electronically glued hardwood plywood with four 1/4-
20 threaded inserts for attachment to frame. The padding material shall be 3” thick polyurethane foam,
shall be glued to the inner surface of the seat panel, and shall conform to the California Bureau of Home
Furnishings Technical Bulletin 117. The seat shall be attached to the frame assembly using (4) 1/4-20 x 1”
pan head machine screws and split lock washers.
D. Back Construction: The back panel shall be 1/2” thick, electronically glued curved hardwood plywood. The
padding material shall be 2” thick polyurethane foam, shall be glued to the inner panel, and shall conform to
the California Bureau of Home Furnishings Technical Bulletin 117. The outside surface of the back panel
shall be encapsulated in 1/4” thick slab polyurethane foam. The back shall be attached to the frame
assembly using (4) 1/4-20 x 1/2” pan head machine screws with external tooth lock washers.
E. Armrests: Shall be kiln-dried solid hardwood, nominally 3/4” thick x 2-1/4” wide x 12” long. Each armrest
will be fastened to the frame assembly using (2) #8 x 3/4” pan head sheet metal screws.
F. The chair shall be equipped with a non-tilt mechanism.
G. The chair shall be equipped with a swivel and return cylinder.