Installation instructions, Emissions standard, Precision ii filter cleaning & oiling – S&B Filters Cold Air Intake Kit - Cotton Filter 75-5028 User Manual
Page 3: Performance testing, Related items for your purchase
EMISSIONS STANDARD
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog
check inspection when a Performance Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit
after installation so that a smog check technician can easily verify the E.O. number. As of April 2009, S&B has never had a product
where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check the
status of the exemption process by looking up a specific part number at
The CARB Exemption number and/or
status is listed under the Product Details section for each part number. If the status shows as “Pending,” CARB has yet to issue an
exemption. Products that have not been issued an EO number are street legal in most states, but may not be used on emission
controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer,
log onto our web site and register to receive your Exemption Sticker.
787 S. Wanamaker, Ontario, CA 91761 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -
INSTALLATION INSTRUCTIONS
PERFORMANCE TESTING
• Engage parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-
inspect hoses and connections as they may need to be repositioned and tightened.
• S&B FILTERS recommends that you keep your OE intake system in the event it is required in the future.
• In order to maintain your warranty, all connections and components must be checked periodically for
alignment and for proper tension on all connections. Failure to do so may void your warranty.
• Use only S&B FILTERS cleaning and oil products to service your filter. Using any other brand oil and or
cleaners on your S&B air filter may void your warranty. Visit
for complete warranty
information.
SEE EXPLODED VIEW ON PAGE 4
3
P/N: 75-5028 / 75-5028D
RELATED ITEMS FOR YOUR
PURCHASE
• Replacement Air Filter (Oiled)
(S&B P/N: KF-1042)
• Replacement Air Filter (Dry)
(S&B P/N: KF-1042D)
• Air Filter Wrap (S&B P/N: WF-1020)
22.
Remove the protective covering from
the Clear Lid
(C)
and place it on the Air Box
(P)
, secure with the 10/24 SS Screws
(A)
and
SS sealing washers
(B)
.
23.
IF EQUIPPED: To reinstall the electronic air restriction gauge drill a 3/4” hole in the Air Box
(P)
or Cold Air Tube
(L)
(Do not drill the Intake Tube
(J)
) and insert the OE grommet into the hole, then
insert the gauge into the grommet. Reconnect the electrical connection. After reconnecting you may
just zip tie it up out of the way of any hot or moving engine components.
NOTE: OE Restriction Gauges are not calibrated for
the S&B Intake Kit, both types (Manual and
Electronic) will no longer be accurate. However, the
electronic type must be reconnected or the indicator
light may be triggered.
Important: Service air filter according to S&B
precision cleaning instructions. Do not rely on the
restriction gauge or wait until the dash light is
triggered.
25.
Reconnect all battery cables, positive
cables first. Inspect your installation, make sure
the kit is properly positioned and all fasteners are
secure. Affix the CARB sticker near the intake
kit. The installation is now complete.
Circled below is the
recommended area for placement
of the gauge if used.
Precision II
Filter Cleaning & Oiling
Order online today at
through your local S&B distributor.
Part #: 88-0008