Installation instructions (continued), Precision ii filter cleaning & oiling, Air box end cap testing – S&B Filters Cold Air Intake Kit - Cotton Filter 75-5043 User Manual
Page 3: Performance testing, Related items for your purchase
787 S. Wanamaker, Ontario, CA 91761 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -
INSTALLATION INSTRUCTIONS (continued)
PERFORMANCE TESTING
• Engage parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-
inspect hoses and connections as they may need to be repositioned and tightened.
• S&B FILTERS recommends that you keep your OE intake system in the event it is required in the future.
• In order to maintain your warranty, all connections and components must be checked periodically for
alignment and for proper tension on all connections. Failure to do so may void your warranty.
• Use only S&B FILTERS cleaning and oil products to service your filter. Using any other brand oil and or
cleaners on your S&B air filter may void your warranty.
3
P/N: 75-5043 / 75-5043D
RELATED ITEMS FOR YOUR
PURCHASE
• Air Scoop Assembly (S&B P/N: AS-5049)
• Air Filter Wrap (S&B P/N: WF-1023)
• Water Protection Scoop Wrap
(S&B P/N: WF-1028)
• Snow Scoop Plug and Mounting Bracket kit
(S&B P/N: 75-5051)
Precision II
Filter Cleaning & Oiling
Order online today at
through your local S&B distributor.
Part #: 88-0008
SEE EXPLODED VIEW ON PAGE 4
Air Box End Cap Testing
Stock air boxes are a significant contributor to poor air flow which is why S&B designs custom air boxes with secondary and/or enlarged openings. With
that said, S&B recognizes the benefits of cooler air, so we have included a plug to seal off the opening if so desired. For optimal performance, we
recommend that the intake be used without the end cap except in conditions of extreme heat. Without the plug installed on the box, there is an additional
improvement in airflow.
Visit the product page for this intake at
to see the actual test results outlined in detail.
Emissions Standard
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog check inspection when a Performance
Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit after installation so that a smog check technician can easily verify the E.O. number.
As of April 2009, S&B has never had a product where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check
the status of the exemption process by looking up a specific part number at
The CARB Exemption number and/or status is listed under the Product Details
section for each part number. If the status shows as “Pending,” CARB has yet to issue an exemption. Products that have not been issued an EO number are street legal in most
states, but may not be used on emission controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer, log onto our web site and register to
receive your Exemption Sticker.
23.
Install the Clear Lid
(P)
using the
supplied 5/16” S.S. Screws
(M)
and Rubber
Washers
(L)
along with the 10-24 Screws
(N)
and SS Sealing Washers
(O)
. This will secure
the Filter Adapter to the Air Box as well.
24.
Reconnect both batteries. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker near the intake kit. The
installation is now complete.