Veris Industries PD SERIES Install - Manual

ZL0055-0D PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 07121
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
TM
EnvironmEntal SEnSorS inStallation GUiDE
Digital Pressure/Vacuum Gauge with Display
and Analog 4-20 mA Output
quick install
1. Select a location for the installation suitable to the gauge’s physical dimensions
that will allow access to the display and keypad. Plan for a ¼" M-NPT connection
or a hose to a ¼" fitting.
2. Thread the gauge onto the fitting. Apply tightening torque only to the metal
wrench flats, not to the PD housing. Use a 5/8” wrench. Do not overtighten.
3. Wire the device. See the wiring diagram in this guide.
4. Remove the protective film from the gauge front.
5. Program the gauge.
Installer’s Specifications
Measurement Units Selectable: psi, bar, kg/cm2, ATM, in. Hg, in. H
2
O*
Accuracy** < ±0.5% of F.S., BFLS
Overange Protection 2x rated pressure
Burst Pressure 5x rated pressure or 5000 psi, whichever is less
Temperature Ranges:
Operating (Ambient) -10° to 70°C (15° to 158°F)
Storage -40° to 65°C (-40° to 150°F)
Thermal Limits:
Compensated Range 0° to 55°C (32° to 131°F)
TC Zero < ±1.5% of F.S.
TC Span < ±1.5% of F.S.
Connection ¼" NPT, male
Power*** 7.5 to 32 VDC
Housing Polycarbonate
Environmental Protection NEMA 4, IP65
Output 4-20 mA loop powered
* in. H2O units available on ≤250 psi range devices only
** Accuracy includes non-linearity, hysteresis and non-repeatability measured at 25°C/77°F
*** Select a loop power supply and total loop resistance such that when the loop current is 20 mA,
the gauge will have at least 7.5 VDC at its terminals.
PD SerieS PD SerieS
Dimensions
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• Read and understand the instructions before installing
this product.
• Turn off all power supplying equipment before working on it.
• The installer is responsible for conformance to all applicable codes.
Range
= 17 - 4 SS
Output
= 4-20 mA
Material
50 = 0 to 50 psig
100 = 0 to 100 psig
250 = 0 to 250 psig
500 = 0 to 500 psig
1000 = 0 to 1000 psig
PD A M
ProDuct iDentification
Zero
VERIS INDUSTRIES
http://www.veris.com
1-800-354-8556
1-503-598-4564
Digital Pressure Gauge
3.6”
(90mm)
4.2”
(106mm)
Calib
2.8”
(72mm)
1.8”
(46mm)
1.4”
(36mm)
2.2”
(56mm)
0.7”
(17mm)
Test Units
5/8”
Front Side Rear
Wrench Flat
(Tighten with a 5/8” wrench at this spot. Do not tighten by twisting the plastic PD housing.