Lubricate wheel end – Spicer Tandem Drive Axles Pro-40 Single Reduction and Single Reduction with Differential Lock User Manual
Page 87
84
90
Wheel End Seal
Lubricate Wheel End
Before operating the axle, the wheel hub cavities and bear-
ings must be lubricated to prevent failure.
When wheel ends are serviced, follow Dana’s wheel end lubri-
cation procedure before operating the axle.
Dana axles may be equipped with either of two wheel end
designs:
•
Wheel ends
with an oil fill hole.
•
Wheel ends
without an oil fill hole.
Wheel Ends with an Oil Fill Hole
7. Rotate the wheel end hub until the oil fill hole is up.
8. Remove the oil fill plug.
9. Pour 1/2 pint of axle sump lubricant into each hub
through the wheel end fill hole.
10. Install oil fill plug and tighten to specified torque.
IMPORTANT
1—Wheel end oil fill hole
2—Proper lubricant level
3—Lubricant flow from sump
3
1
2
Wheel End with Oil Fill Hole
Wheel End without Oil Fill Hole
- DSP40 Tandem Axle - Dare to Compare (2 pages)
- Ratio Flex Program Guide (46 pages)
- Italcardano Wing In A Box Product Line (3 pages)
- Vibration Diagnostics (1 page)
- Carrier-To-Housing Joint Leak (6 pages)
- Front Axle Shafts for the Jeep JK (2 pages)
- S400 Helical Gear Retrofit Kit Installation (2 pages)
- Electric Shift Unit (1 page)
- Approved Lubricant (16 pages)
- Kingpin Bushing and Seal Installation Instructions (2 pages)
- ROUND BEARING DRIVESHAFT COMPONENTS (11 pages)
- NEW REDESIGNED 40K TANDEM CARRIERS (6 pages)
- HAXL-PNI-34 (1 page)
- Tandem Drive Axles Service Manual S400 (34 pages)
- HAXL-PNI-31 (1 page)
- Single Drive Axles Service Manual: S170, S190, S590 (76 pages)
- PDU Cover & Outer Pinion Support Bearing for 46,000 LB (2 pages)
- 2007 Spicer Driveshafts Service Manual (32 pages)
- DRIVELINE COMPONENTS CATALOG SLIP YOKE ASSEMBLIES (28 pages)
- DualRange Tandem Axles (8 pages)
- S400 Redesigned Power Divider Parts for Service (2 pages)
- Wing Bearing Products U-Joint Identification Chart (1 page)
- 10 Series Driveshafts (86 pages)
- Driveline Components Catalog - Companion Flanges (24 pages)
- Gear & Pinion and Wheel Diff Case Kits Released for D_R170, D_R190 Models (3 pages)
- DST40-(P) (3 pages)
- 22719X, MODEL 44 POWER LOCK DISC AND PLATE KIT (1 page)
- 126155 (1 page)
- 2011 Spicer Bulletin 3; SERVICE_TECHNICAL INFORMATION (1 page)
- Drive Axles Service Manual Single Axles 2-Speed & Double Reduction (34 pages)
- X510-5DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS (2 pages)
- Dana “I” Series (2 pages)
- Elimination of PDU Fill Plug On Tandem Drive Axles (2 pages)
- V Drive Components (1 page)
- RST41 (1 page)
- Torsionally Tuned-40 Tandem Drive Axles (2 pages)
- Drive Axles Illustrated Parts List DSS40, DDS40, RSS40, and RDS40 (28 pages)
- Single Drive Axles Service Manual: S140 Series (44 pages)
- DRIVELINE COMPONENTS CATALOG COUPLING SHAFTS - SPL and 10 Series (16 pages)
- Thick Flange Design Carriers (2 pages)
- 2002 Spicer Bulletin; SERVICE_TECHNICAL INFORMATION (1 page)
- Pre-applied Thread Adhesive Compound on Yoke End Nuts (6 pages)
- U-Tube Breather Assembly (2 pages)
- 130542 (1 page)