Vertex Standard FT-1000MP - Manual (Page 36)

Page 34 O
PERATING
M
ANUAL
ANT Coaxial Jacks
Connect your main antenna(s) here, using a type-
M (PL-259) plug and coaxial feedline. These antenna
ports are always used for transmission, and also are
used for reception unless a separate receive antenna
is also used for the main receiver. The internal antenna
tuner affects only the antenna(s) connected here, and
only during transmission.
REMOTE Jack
By plugging in a remote control keypad here, direct
access to the MARK-V FT-1000MP
Field CPU is pro-
vided for control functions such as contest memory key-
ing, frequency, and function control. This jack may also
be also used for remote control of the VL-1000 Linear
Amplifier, if used.
CW SIDETONE Trimmer
Insert a small insulated screwdriver here and turn
the trimmer inside to adjust the volume of the sidetone
heard during CW keying (and when the [SPOT] button
is pressed).
KEY 3-Contact Phone Jack
This ¼-inch phone jack accepts a CW key or keyer
paddle. It is connected in parallel with the jack with the
same name on the front panel (either or both may be
used). A 2-contact plug cannot be used in this jack.
Key-up voltage is +5 V, and key-down current is 0.5
mA. Plug wiring is shown on page 4.
BACKUP Slide Switch
Keep this switch in the “ON” position to retain all
memory and VFO settings during power-off periods.
There is no need to turn this switch off unless you plan
to store the transceiver for a long period without use.
R
EAR
P
ANEL
C
ONTROLS
& C
ONNECTORS
CAT Serial DB-9 Jack
This 9-pin serial DB-9 jack allows external com-
puter control of the MARK-V FT-1000MP Field. Con-
nect a serial cable here and to the RS-232C COM port
on your personal computer (no external interface is re-
quired).
CAT command protocol and data formats are
described in the
CAT chapter, starting on page 86.
DVS-2 DIN Jack
This 7-pin input/output jack is for connection of the
DVS-2 Digital Voice Recording option, described on
page 81.
PACKET DIN Jack
This 5-pin input/output jack provides receiver au-
dio and squelch signals, and accepts transmit (AFSK)
audio and PTT control, from an external Packet TNC.
Pinout is shown on pages 4 and 16. The receiver au-
dio level at this jack is approximately 100 mV (@600
Ohms), preset by VR3010 on the AF Unit (see page
15 for access to this trimmer, if necessary).
RTTY DIN Jack
This 4-pin input/output jack provides connections
for an RTTY terminal unit. Pinout is shown on pages 4
and 17. The receiver audio level at this jack is at a
constant 100-mV (@600 Ohms) level. FSK keying at
this jack is accomplished by a closure of the SHIFT
line to ground by the terminal unit.
PTT Phono Jack
This input jack may be used to provide manual trans-
mitter activation using a footswitch or other switching
device. Its function is identical to the [MOX] button on
the front panel. The same line is available at the PACKET
and RTTY jacks for TNC control. Open-circuit voltage is
+13.8 VDC, and closed-circuit current is 1.5 mA.
REMOTE
B A ANT
KEY BACKUP
LIN
CAT DVS-2
BAND DATA
+13.8V TRV TX GND RX ANT
PACKET RTTY PTT
EXT
ALC
EXT
SPKR PATCH AF OUT
GND OFF
O F F
IN OUT
CW
SIDETONE ON
ACC
ON
OUTPUT
DC 13.8V
200 mA
INPUT
DC 13.8V
20 A
INPUT
AC 100-120V ~
50-60Hz 6A FUSE
T8A
DC IN ~ AC IN