Texas Instruments TMS3320C5515 User Manual
Page 72
System Configuration and Control
www.ti.com
1.7.4.2.1 DMA Interrupt Flag Register (DMAIFR) [1C30h] and DMA Interrupt Enable Register (DMAIER)
[1C31h]
The DSP includes two registers for aggregating the four channel interrupts of the four DMA controllers.
Use the DMA interrupt enable register (DMAIER) to enable channel interrupts. At the end of a block
transfer, if the DMA controller channel interrupt enable (DMAnCHmIE) bit is 1, an interrupt request is sent
to the DSP CPU, where it can be serviced or ignored. Each channel can generate an interrupt, although
all channel interrupts are aggregated into a single DMA interrupt signal to the CPU.
To see which channel generated an interrupt, your program can read the DMA interrupt flag register
(DMAIFR). The DMA controller channel interrupt flag (DMAnCHmIF) bits are set to 1 when a DMA
channel generates an interrupt. Your program must manually clear the bits of DMAIFR by writing a 1 to
the bit positions to be cleared.
Figure 1-42. DMA Interrupt Flag Register (DMAIFR) [1C30h]
15
14
13
12
11
10
9
8
DMA3CH3IF
DMA3CH2IF
DMA3CH1IF
DMA3CH0IF
DMA2CH3IF
DMA2CH2IF
DMA2CH1IF
DMA2CH0IF
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
7
6
5
4
3
2
1
0
DMA1CH3IF
DMA1CH2IF
DMA1CH1IF
DMA1CH0IF
DMA0CH3IF
DMA0CH2IF
DMA0CH1IF
DMA0CH0IF
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Figure 1-43. DMA Interrupt Enable Register (DMAIER) [1C31h]
15
14
13
12
11
10
9
8
DMA3CH3IE
DMA3CH2IE
DMA3CH1IE
DMA3CH0IE
DMA2CH3IE
DMA2CH2IE
DMA2CH1IE
DMA2CH0IE
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
7
6
5
4
3
2
1
0
DMA1CH3IE
DMA1CH2IE
DMA1CH1IE
DMA1CH0IE
DMA0CH3IE
DMA0CH2IE
DMA0CH1IE
DMA0CH0IE
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
RW-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 1-54. DMA Interrupt Flag Register (DMAIFR) Field Descriptions
Bit
Field
Value
Description
15-0
DMAnCHmIF
Channel interrupt status bits.
0
DMA controller n, channel m has not completed its block transfer.
1
DMA controller n, channel m block transfer complete.
Table 1-55. DMA Interrupt Enable Register (DMAIER) Field Descriptions
Bit
Field
Value
Description
15-0
DMAnCHmIE
Channel interrupt enable bits.
0
DMA controller n, channel m interrupt is disabled.
1
DMA controller n, channel m interrupt is enabled.
72
System Control
SPRUFX5A – October 2010 – Revised November 2010
Copyright © 2010, Texas Instruments Incorporated